Adding a Schrader Valve to a Homebrew Keg
Adding a Schrader Style Valve to a Homebrew Keg
This was really just a matter of putting the right fittings together. Pictured: Milton (S-684-4) 1/4″ MNPT Male Tank Valve – Anderson Metals Brass Pipe Fitting, Coupling, 1/4″ x 1/4″ Female Pipe – LASCO 17-6783 1/4-Inch Female Flare by 1/4-Inch Male Pipe Thread Brass Adapter
Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.
A quick check to make sure all of this fit together
Everything tightened down with teflon tape
This assembly is a tank/Schrader style valve to a 1/4″ x 1/4″ female to female coupling to a 1/4″ NPT to 1/4″ flare fitting. All that to say, I have this threaded onto a ball lock QD here, but it could just as easily thread into an MFL pin lock QD.
Installed and pressurized.
Posts Featuring this Assembly
- Using a Keg as a CO2 Source for Portable Serving
- Using a Tire Inflator as a Pressure Source for Portable Serving
- Using a Tire Inflator To Check for Keg Leaks
Assembly Components
The parts and pieces I used, all via Amazon:
- Milton (S-684-4) 1/4″ MNPT Male Tank Valve
- Anderson Metals Brass Pipe Fitting, Coupling, 1/4″ x 1/4″ Female Pipe
- LASCO 17-6783 1/4-Inch Female Flare by 1/4-Inch Male Pipe Thread Brass Adapter
- OneBom Ball Lock Disconnect, Gas & Liquid Corny Keg Fittings, MFL 1/4’’ Threaded with 5/16’’ Stainless Steel Barbed & Hose Clamp (Ball Lock Kit)
- Dixon Valve TTB75 PTFE Industrial Sealant Tape, -212 to 500 Degree F Temperature Range, 3.5mil Thick, 520″ Length, 3/4″ Width, White
Important: Make sure every component in your setup is rated for the amount of pressure you decide to use.
Related: Use a Spare Keg as a CO2 Source for Portable Serving
More Homebrew Finds!
- Last 50 Finds!
- Top Deals – a curated list of the best deals
- Homebrew Reviews – one of the largest libraries of homebrew reviews in existence!
- Our Top Posts – tips, how-tos, resources posts and more
- Let’s be Friends!
Recent Deals!
10 Most Recent Homebrew Resource Posts & How-To’s!
We are Homebrew Review HQ! Our 10 Most Recent Reviews
pinnedThis post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
greatdealsMake sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions. tag:lnksfxd toppost:kegshrader tag:tpr
Thank you for posting this.
If it weren’t for this I would not have realized that the threading of the post on the QD was different from that of the schrader valve (MFL vs NPT).
I’ve done this. It’s very useful for pressure testing empty kegs without wasting CO2. Use an air compressor (or bicycle pump for a good workout) to inflate the keg, just like a car tire. Then spray StarSan or soapy water around the fittings and lid gasket to check for leaks.
Mine uses a 1/4″ FPT to barb adapter to connect the Schraeder valve to a bit of air tube, then to a barbed ball lock disconnect. I believe that would be a cheaper build than this.