Category Archives: Kegerator

Yaebrew FIVE Way CO2 Manifold w/Shutoffs & Check Valves

YaeBrew Gas Manifold, Beer Gas Distributor, Air Distributor CO2 Manifold 5/16" - 5 Way

5 way CO2 Manifold by YaeBrew


From the product description, check product page for current description, price and availability:

  • 5/16” barbed inlets and outlets
  • Shutoffs with built-in check valves
  • YaeBrew Gas Manifold, Beer Gas Distributor, Air Distributor CO2 Manifold 5/16″ – 5 Way

Use to pressurize multiple kegs off one co2 regulator.

YaeBrew Gas Manifold, Beer Gas Distributor, Air Distributor CO2 Manifold 5/16″ – 5 Way – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

ARCTIC F12-120 mm Case Fan [Stir Plate Project, Kegerator Circulation]

ARCTIC F12-120 mm Standard Low Noise Case Fan - Fluid Dynamic Bearing - Innovative Design

ARCTIC F12 – 120 mm Standard Case Fan, very quite motor, Computer, Push- or Pull Configuration, Fan Speed: 1350 RPM

More Info

From the product description, check product page for current description, price and availability:

  • INNOVATIVE DESIGN: Design of fan blades improves airflow and facilitates efficient ventilation, impeller was designed with a focus on minimzing the noise level yet delivering the desired airflow and pressure
  • TWO WAY INSTALLATION: Blow warm air out of the case, draw cool air into your case
  • LONG SERVICE LIFE: The Fluid Dynamic Bearing comes with an oil capsule that avoids lubricant leakage, thus this bearing is as quiet as a sleeve bearing but comes with a higher service life
  • TECHNICAL DATA: Fan speed: 1350 RPM, Airflow: 53 CFM/90;1 m³/h (@ 1350 RPM), Noise Level: 0;3 Sone (@ 1350 RPM), Pin: 3-pin

From HBF: Make sure the components you use are compatible and rated for your intended application.  Contact manufacturer with questions about suitability or a specific application.  Always read and follow manufacturer directions.

 

ARCTIC F12 – 120 mm Standard Case Fan, very quite motor, Computer, Push- or Pull Configuration, Fan Speed: 1350 RPM affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

2 Way CO2 Manifold w/Shutoffs & Check Valves

2-Way Gas Manifold CO2 Distributor Manifold 5/16 inch Barb/Stem Splitter Beer Integrated Check Valves Homebrew Beer Making Brewing Tool

Two Way CO2 Manfiold.  Shut offs & built in check valves

More Info

From the product description, check product page for current description, price and availability:

  • 🍺 Gas Manifold, A built-in check valve protects your shunt and prevents gas back flow.
  • 🍺 Due to the one-way valve mechanism, the pressure drop between the ball valves in these manifolds is approximately 2 psi. You will need to set the pressure on the regulator to 2 psi above the pressure required in the keg.
  • 🍺 Run multiple lines from one CO2 source. The distributor allows you to split the gas supply into multiple lines. Each line has its own shutoff valve.
  • 🍺 There is a 2-point screw hole on the top for easy installation to other equipment. 5/16″ barbed inlet and 5/16″ barbed outlets.
  • 🍺 Made of aluminum, brass and stainless steel material, it is extremely durable.

 

Use to pressurize multiple kegs off one co2 regulator

2-Way Gas Manifold CO2 Distributor Manifold 5/16 inch Barb/Stem Splitter Beer Integrated Check Valves Homebrew Beer Making Brewing Tool – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Finally In Stock… KOMOS Gas Manifolds – Easy Conversion to DuoTight

KOMOS® Aluminum Gas Manifold – 1/4 in. Flare via MoreBeer

From the product description, check product page for current description, price and availability:

Due to high demand, the 3 & 4 way manifold is currently out of stock. Be the first to receive your items by placing a pre-order today. We will automatically ship this item to you when we receive more inventory.

Gas manifolds are the best way to provide CO2 to multiple kegs inside your kegerator or keezer. The KOMOS manifold features 1/4″ flare gas inlet and check valves that provide much more flexibility compared to manifolds with barbed valves. Choose the type and size of draft tubing that you prefer. Use 1/4″ or 5/16″ gas line with the appropriate Flare Fitting Set (KEG607 or KEG640), or use EVABarrier—our draft line of choice—with the appropriately sized Duotight Fitting (DUO106 or DUO120).

You can also replace one or more of the check valves with a Ball Lock Post Bulkhead, which allows you to use a gas-in ball lock jumper line as a quick connect option.

Need something bigger than a 4-way manifold? No problem! With this 1/4″ Nipple, you can join multiple manifolds for as many outlets as you need.

Features:

  • 1/4″ Flare connections
  • 1/4″ BSP ball valves
  • Rated to 100 psi
  • Wall mount holes
  • Made from aluminum, brass, and stainless steel

[/expand]

 

  • These have been out of stock for a long, long time. As of this posting, they’re back in stock. Check the product page to see if you can still get in on this shipment.
  • Get Free Shipping: Shipping is free with a qualifying $59 order to many US addresses
  • Some filler item ideas to help you qualify for free shipping… PBW, Sale Items (shows most popular deals first), Kit of the Week, Hop Market (shows most popular deals first)

KOMOS® Aluminum Gas Manifold – 1/4 in. Flare

Convert to DuoTight!

Build a DuoTight CO2 Gas Manifold! – for Kegland EVABarrier Tubing

Want to Learn More about DuoTights and EVABarrier Tubing?  

duotightreview

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

6 Faucet Caps + 3 Brush Plugs

CM 6 Pcs Beer Tap Cover Draft Faucet Keg Caps Tap Cap Tap Soother and 3 Pcs Beer Tap Plugs Brush Draft Faucet Keg Brush Plugs

CM 6 Pcs Beer Tap Cover Draft Faucet Keg Caps Tap Cap Tap Soother and 3 Pcs Beer Tap Plugs Brush Draft Faucet Keg Brush Plugs

More Info


Highlighted Features
  • Beer Draft Faucet Keg Tap Cover Cap: Keep your tap sealed. Keep faucets clean and sanitary.
  • Beer Tap Plugs Brush: Clean faucet taps and remove sediment for better beer tasting.
  • Great combo set with two different products to keep faucet keg taps.
  • Durable material and easy to clean. Please check the size for reference.
  • Each pack with Tap Cover Cap x 6 Pcs, Beer Tap Plugs Brush x 3 Pcs and Marble Pattern Drawstring Pouch Bag x 1 pc.

 

 

CM 6 Pcs Beer Tap Cover Draft Faucet Keg Caps Tap Cap Tap Soother and 3 Pcs Beer Tap Plugs Brush Draft Faucet Keg Brush Plugs – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Coldbreak Brewing Stainless Steel Forward Sealing Faucet

Coldbreak Brewing Equipment Forward Sealing Beer Faucet, Wine Faucet, Stainless Steel, Black Tap Handle Included, Standard

Coldbreak Brewing Equipment Forward Sealing Beer Faucet, Wine Faucet, Stainless Steel, Black Tap Handle Included, Standard

More Info

From the product description, check product page for current description, price and availability:

  • Commercial stainless steel wine faucet with stainless steel lever
  • Easy to take apart and clean
  • Polished interior and forward sealing design for smooth operation
  • Standard tap threads (black tap handle included)

 

Coldbreak Brewing Equipment Forward Sealing Beer Faucet, Wine Faucet, Stainless Steel, Black Tap Handle Included, Standard – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

MoreBeer Beer Faucet Bonnet Angler – $6.99 + Free Ship Eligible, Limited Availability

 Beer Faucet Bonnet Angler D1270

Beer Faucet Bonnet Angler from MoreBeer

More Info

From the product description, check product page for current description, price and availability:

Also called a faucet positioner because it angles big tap handles from touching the wall or refrigerator. Installs on top of beer faucet lever and then the tap handle thread into this bonnet angler.


 

Limited Availability Deal of the Day: As of this posting, this is marked down to $6.99 as a MoreBeer Deal of the DayShipping is also free to addresses in the contiguous US with most $59 Orders. Availability: This is available today only, while supplies last. Quantities are limited. Check the MoreBeer’s Deal of the Day to check today’s offering.

Product Description – Here – Use coupon code BEERDEAL to get this discount

Beer Faucet Bonnet Angler D1270

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

2 Way CO2 Manifold w/Shutoffs & Check Valves

Gas Manifold, Beer Gas Distributor, Air Distributor CO2 Manifold - Splitter 5/16" Barb Fittings (2 way 5/16" Barb)

Gas Manifold, Beer Gas Distributor, Air Distributor CO2 Manifold – Splitter 5/16″ Barb Fittings (2 way 5/16″ Barb)

More Info

From the product description, check product page for current description, price and availability:

  • The gas manifold body is made of high quality aluminum. The inlet barb & hexagon nut is made of brass. The switch valve is made of copper plated zinc.So our gas manifold is lighter & durable than steel
  • 2 way gas manifold allow you to supply CO2 for your several beer kegs. The gas manifold also provide the extra gas inlet for beer keg
  • 【No Leaks & Independent Shunt】: The integrated check valves can prevent backflow of gas or liquid and protect your splitter. Every switch valve has their handles to control the gas flow,so each gas line will not affect the airflow of other kegs
  • 【Easy To Use】: The gas manifold come with 5/16″ barb OD outlets & inlets. Inlet barb can connect with CO2 tank by hose. And the barb of shutoff valve can connect with your keg by hose to achieve carbonating beer
  • 【Faster To Install】:Just need two screws or nails,you can easily secure this gas manifold on walls or kegerators. A gas manifold can split the delivery of CO2 into several parts to serve the draft beer system

 

Use to pressurize multiple kegs off one co2 regulator.

Gas Manifold, Beer Gas Distributor, Air Distributor CO2 Manifold – Splitter 5/16″ Barb Fittings (2 way 5/16″ Barb) – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link


Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Kingwin 120 mm Case Fan [Stir Plate Project, Kegerator Circulation]

Kingwin 120mm CF-012LB Silent Fan, For Computer Cases, CPU Coolers, Long Life Bearing, Quiet Efficient Cooling, and Provide Excellent Ventilation for PC Cases-[Black]

Kingwin 120mm CF-012LB Silent Fan, For Computer Cases, CPU Coolers, Long Life Bearing, Quiet Efficient Cooling, and Provide Excellent Ventilation for PC Cases-[Black]
More Info

From the product description, check product page for current description, price and availability:

  • Designed to quietly cool Xboxs, Playtations, Rokus, TVs, receivers, mondems, routers, DVRs, computers, and other audio video electronics.
  • Features a multi-speed controller to set the fan’s speed to optimal noise and airflow levels.
  • Dual-ball bearings have a lifespan of 50,000 hours and allows the fans to be laid flat or stand upright
  • The power adapter increases maximum fan speed and enables the fan to be powered through an AC outlet.
  • 120 x 120 x 25 mm ( 4.72 x 4.72 x 1 in. ) | Rated Voltage :12V | Airflow: 92.3 ±10%CFM | Rated Current: 0.45A | Speed: 3000 RPM | Power: less than 2W at slowest speed ; 4.4 W at full speed

 

Kingwin 120mm CF-012LB Silent Fan, For Computer Cases, CPU Coolers, Long Life Bearing, Quiet Efficient Cooling, and Provide Excellent Ventilation for PC Cases-[Black] – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link


This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Make sure the components you use are compatible and rated for your intended application.  Contact manufacturer with questions about suitability or a specific application.  Always read and follow manufacturer directions.

Two Pressure CO2 Regulator [multiple carbonation levels and more]

MOD Complete MDC99007 CO2 Beer Regulator Dual Pressure

More Info



 

Why a two pressure regulator?  A two pressure regulator gives you the ability to keep kegs at different pressures.  This is a requirement to maintain two distinct carbonation levels.  It’s also handy if you want to force carbonate a keg more quickly, at a higher pressure, while maintaining your standard serving pressure on a keg that’s already being served or if you want to have a utility line for purging kegs and such.

MOD Complete MDC99007 CO2 Beer Regulator Dual Pressure Kegerator Heavy Duty Features T-Style Adjusting Handle – 0 to 60 PSI-0-3000 Tank Pressure CGA-320 Inlet w/ 3/8″ O.D. Safety Discharge 50-55 PSI – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft


This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

The Weekend Brewer 3-way MFL CO2 Manifold + Convert it to DuoTight

The Weekend Brewer 3-way MFL CO2 Distributor Manifold with integrated check valves

The Weekend Brewer 3-way MFL CO2 Distributor Manifold with integrated check valves

More Info

From the product description, check product page for current description, price and availability:

  • Light and durable aluminum body is lighter than steel but remains Durable and long lasting. Aluminum is the industry standard for Co2 manifolds for their strength and resistance to corrosion. This manifold is ideal for homebrewers, bars, or anyone who is looking to easily split gas for beer or beverage dispensing and even for force carbonation.
  • Integrated high quality check valve outputs prevent liquid from flowing into the manifold and your regulator. Don’t worry about dirty lines or ruined regulators ever again! Every integrated check valve ensures that your beer stays on the right side of the line.
  • No leaks due to ample thread tape and vigorous water testing after assembly. All manifolds are internally cleaned before assembly for the purest air possible. Don’t settle for mass produced, low quality manifolds from overseas. The Weekend Brewer manifold is the highest quality manifold on the market due to rigorous testing and quality control.
  • Mounting holes allows for easy installation on walls or kegerators. Two screws or nails will easily secure your manifold to any surface for ease of use.
  • Made in the USA these manifolds are assembled by American workers in our fayetteville, AR facility.

 

 

CO2 manifolds allow you to feed multiple kegs off one co2 regulator.  Things to look for in a capable manifold are shut-off valves for each trunk and check valves.  Check valves makes sure flow goes the right directly.  This is important for CO2 manifolds because differences in pressure make it possible for liquid to back flow through gas lines.

I have two posts about the 4 way version of this manifold.  A Hands on Review and a walk-through to convert it to DuoTight.

The Weekend Brewer 3-way MFL CO2 Distributor Manifold with integrated check valves – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Build a DuoTight CO2 Gas Manifold! – for Kegland EVABarrier Tubing

duotightreview

ORIA Refrigerator Freezer Thermometer with TWO Wireless Sensors – monitor kegerator & fermentation chamber temps

ORIA Refrigerator Thermometer, Wireless Digital Freezer Thermometer with 2 Wireless Sensors, Wireless Indoor Outdoor Thermometer, Audible Alarm, Min and Max Display, LCD Display for Home, Restaurants

ORIA Refrigerator Thermometer

More Info

Highlighted Features
  • Note: 1. The host and the transmitter can receive good reception within 100 meters of the unobstructed distance. Indoor temperature detection range -10°C-60°C (32°F-122°F); Outdoor sensor temperature receiving range -40°-60° (-40°F-140°F); 2. After the temperature alarm is turned on, the alarm function will not be activated until 10 minutes later (when it is just turned on, no matter whether the temperature reaches the alarm temperature range at this time, it will not alarm) 3. Please place this thermometer properly to prevent the screen from being crushed.
  • Max/Min Temperature: The Max/ Min temeprature data will update every 24h. Pls be attention that the product cannot hold the max/min temperature all the time. The product is not support to view all the recorded previous temperatures. You can press button CLEAR once quickly to remove the Min/Max temperaturen data. And it will update to the new data. The indoor temperature detection cycle is 10 seconds, the outdoor synchronous cycle sensor 1 is 57 seconds, and sensor 2 is 67 seconds.
  • Alarm Function: With audible alarm, you can set the maximum and minimum alarm value manually. It can ring when the temperature value reaches at the point of limit max or min alarm value that you pre-set. After turning on the temperature alarm, the alarm function will only start after 10 minutes (when it is first turned on, regardless of whether the temperature has reached the alarm temperature range, it will not sound an alarm)
  • Easy to Use: There are 6 function keys on the main unit and signal indicator on the transmitter, you just press the corresponding key to turn on/off the alarm, switch the Celsius or Fahrenheit.
  • Easy to Install: With integrated magnets, a hanging hole and a bracket at the back, you can put the main unit in refrigerator door, hang on the wall or stand on the table. Please install the new battery to make sure the accuracy. If the screen does not display content, please check to ensure that the transmitter is connected to the host.


From HBF: Make sure the components you use are compatible and rated for your intended application.  Contact manufacturer with questions about suitability or a specific application.  Always read and follow manufacturer directions.

 

Thoughts from HBF… So, this has two wireless sensors along with an ambient thermometer that’s built into the main unit.  It also records minimum and maximum temps for each sensor.  You could use one sensor in your fermentation chamber and one sensor in your kegerator to monitor temperatures.  The min and max feature would also give you a great idea about how things are working.  As a bonus you also get all the same info for the ambient temp where the base is located.  Note that the sensors need to be within the stated range of this unit (or closer).

What are Other’s Saying?   Search this product’s Amazon reviews for “kegerator” – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

ORIA Refrigerator Thermometer, Wireless Digital Freezer Thermometer with 2 Wireless Sensors, Wireless Indoor Outdoor Thermometer, Audible Alarm, Min and Max Display, LCD Display for Home, Restaurants – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Inkbird IBS-TH2 Logging Thermometer + Probe [Monitor Kegerator & Fermentation Temps] – works with Android & iOS

Inkbird Smart Thermometer Temperature and Humidity Monitor Hygrometer Indoor, Free APP for iOS and Android, IBS-TH2 Plus Version Supports External Temperature Probe and Digital Display

Inkbird Smart Thermometer Temperature and Humidity Monitor Hygrometer Indoor, Free APP for iOS and Android, IBS-TH2

More Info

From the product description, check product page for current description, price and availability:

  • 🌡Maximum range of 98ft(without obstacle) via Bluetooth connection
  • 🌡Built-in temperature & humidity sensor, stores a maximum of 30,000 points of data on the device. Temperature sensor -40℉~140℉ and humidity 0%RH-99%RH
  • 🌡Graph, accuracy calibrating, high/low-temperature alarm notification, data export, and the sampling interval set are supported via the app.Please note that IBS-TH2 is not compatible with the gateway (IBS-M1)
  • 🌡Digital LCD displays temperature and humidity, Bluetooth signal, and remaining battery power. An external waterproof temp probe is included
  • 🌡Smart thermometer supports connection to multiple phones or reading multiple sensors with one cellphone

 

Possible uses include monitoring kegerator temperatures, beer fridge temperatures and fermentation chamber/area temperatures.

This includes a waterproof temperature probe. From what I’ve gathered it looks like you can use it with or without the probe.

This has a hygrometer function as well.  That shows % relative humidity and could be handy for judging whether your Eva Dry (or similar) needs recharged for the purpose of handling excess kegerator and fermentation chamber wetness.  See: Damp Kegerator? Fix Kegerator Condensation

Inkbird Smart Thermometer Temperature and Humidity Monitor Hygrometer Indoor, Free APP for iOS and Android, IBS-TH2 Plus Version Supports External Temperature Probe and Digital Display – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Cheap Drip Tray? 12″x4″ Silicone Tray

Happitasa Silicone Kitchen Sink Organizer Tray, Sponge Holder and Countertop Protector | Straight Lines Style (Black, 12"x4")

Happitasa Silicone Kitchen Sink Organizer Tray, Sponge Holder and Countertop Protector | Straight Lines Style (Black, 12″x4″)

More Info

From the product description, check product page for current description, price and availability:

  • KEEP YOUR PRECIOUS COUNTERTOPS DRY AND FREE FROM DISGUSTING SLIME AND MILDEW | With ample surface area for frequently used sink and counter items
  • BEST IN CLASS & BUILT TO LAST | Up to 3X more high quality silicone than similar products. See for yourself by comparing the weight and thickness of our trays to theirs!
  • PROTECT SURFACES FROM HEAT DAMAGE | Heat resistant to 450F/232C.
  • EASY TO CLEAN | Simply handwash with a warm soapy sponge/scrubber OR pop into the dishwasher!
  • USE THROUGHOUT YOUR HOME | In the kitchen, bathroom or any room, choose the size that works best for you in the color that complements or accents your decor.

From HBF: Make sure the components you use are compatible and rated for your intended application.  Contact manufacturer with questions about suitability or a specific application.  Always read and follow manufacturer directions.

 

This is intended to be used as a sink organizer, but it looks like it would make a fine budget drip tray to me

Happitasa Silicone Kitchen Sink Organizer Tray, Sponge Holder and Countertop Protector | Straight Lines Style (Black, 12″x4″) – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

adamztop5

Inkbird IBS-TH2 Logging Thermometer + Probe [Monitor Kegerator & Fermentation Temps] – works with Android & iOS

Inkbird Smart Thermometer Temperature and Humidity Monitor Hygrometer Indoor, Free APP for iOS and Android, IBS-TH2 Plus Version Supports External Temperature Probe and Digital Display

Inkbird Smart Thermometer Temperature and Humidity Monitor Hygrometer Indoor, Free APP for iOS and Android, IBS-TH2

More Info

From the product description, check product page for current description, price and availability:

  • 🌡Maximum range of 98ft(without obstacle) via Bluetooth connection
  • 🌡Built-in temperature & humidity sensor, stores a maximum of 30,000 points of data on the device. Temperature sensor -40℉~140℉ and humidity 0%RH-99%RH
  • 🌡Graph, accuracy calibrating, high/low-temperature alarm notification, data export, and the sampling interval set are supported via the app.Please note that IBS-TH2 is not compatible with the gateway (IBS-M1)
  • 🌡Digital LCD displays temperature and humidity, Bluetooth signal, and remaining battery power. An external waterproof temp probe is included
  • 🌡Smart thermometer supports connection to multiple phones or reading multiple sensors with one cellphone

 

Possible uses include monitoring kegerator temperatures, beer fridge temperatures and fermentation chamber/area temperatures.

This includes a waterproof temperature probe. From what I’ve gathered it looks like you can use it with or without the probe.

This has a hygrometer function as well.  That shows % relative humidity and could be handy for judging whether your Eva Dry (or similar) needs recharged for the purpose of handling excess kegerator and fermentation chamber wetness.  See: Damp Kegerator? Fix Kegerator Condensation

Inkbird Smart Thermometer Temperature and Humidity Monitor Hygrometer Indoor, Free APP for iOS and Android, IBS-TH2 Plus Version Supports External Temperature Probe and Digital Display – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

The Weekend Brewer 3-way MFL CO2 Manifold + Convert it to DuoTight!

The Weekend Brewer 3-way MFL CO2 Distributor Manifold with integrated check valves

The Weekend Brewer 3-way MFL CO2 Distributor Manifold with integrated check valves

More Info

From the product description, check product page for current description, price and availability:

  • Light and durable aluminum body is lighter than steel but remains Durable and long lasting. Aluminum is the industry standard for Co2 manifolds for their strength and resistance to corrosion. This manifold is ideal for homebrewers, bars, or anyone who is looking to easily split gas for beer or beverage dispensing and even for force carbonation.
  • Integrated high quality check valve outputs prevent liquid from flowing into the manifold and your regulator. Don’t worry about dirty lines or ruined regulators ever again! Every integrated check valve ensures that your beer stays on the right side of the line.
  • No leaks due to ample thread tape and vigorous water testing after assembly. All manifolds are internally cleaned before assembly for the purest air possible. Don’t settle for mass produced, low quality manifolds from overseas. The Weekend Brewer manifold is the highest quality manifold on the market due to rigorous testing and quality control.
  • Mounting holes allows for easy installation on walls or kegerators. Two screws or nails will easily secure your manifold to any surface for ease of use.
  • Made in the USA these manifolds are assembled by American workers in our fayetteville, AR facility.

 

 

CO2 manifolds allow you to feed multiple kegs off one co2 regulator.  Things to look for in a capable manifold are shut-off valves for each trunk and check valves.  Check valves makes sure flow goes the right directly.  This is important for CO2 manifolds because differences in pressure make it possible for liquid to back flow through gas lines.

I have two posts about the 4 way version of this manifold.  A Hands on Review and a walk-through to convert it to DuoTight.

The Weekend Brewer 3-way MFL CO2 Distributor Manifold with integrated check valves – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Build a DuoTight CO2 Gas Manifold! – for Kegland EVABarrier Tubing

duotightreview

25-Pack EPDM Beer Line Coupling Washers – fresh gaskets for your shanks

JET Home Brewing Supply Brand 25-Pack EPDM Beer Line Coupling Washe

JET Home Brewing Supply Brand 25-Pack EPDM Beer Line Coupling Washe

More Info

From the product description, check product page for current description, price and availability:

  • High Quality Food Grade EPDM Rubber
  • Standard size for keg couplers and shanks
  • 13/16″ OD x 1/2″ ID and 1/8″ Thick
  • Made by Jet Gasket & Seal Co

 

JET Home Brewing Supply Brand 25-Pack EPDM Beer Line Coupling Washe – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

K&B Curved Surface Mount Drip Tray 12″ x 6.75″

K&B Surface Mount Drip Tray - Variations (Plastic Kegerator Top Surface Mount Drip Tray, 12" x 6.5")

K&B Surface Mount Drip Tray – Variations (Plastic Kegerator Top Surface Mount Drip Tray, 12″ x 6.5″)

More Info

From the product description, check product page for current description, price and availability:

  • K&B Kegerator Top Drip Tray made of heavy duty black plastic with a small cut out for draft beer tower
  • All K&B Drip Trays come with a complimentary microfiber cleaning cloth as well as a 1 Year Manufacturer’s Warranty
  • Dimensions – 12″ Width x 6.5″ Depth

 

K&B Surface Mount Drip Tray – Variations (Plastic Kegerator Top Surface Mount Drip Tray, 12″ x 6.5″) – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds

Our Top Draft Resources!

Check our our Top Draft Related Resources

standarddraft

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Wrap Around Kegerator Drip Tray Bar Mat

12×7 inches PVC Drip Tray for Home Brewing, Kegerator (Black)

12×7 inches Drip Tray for Home Brewing, Kegerator

More Info


Highlighted Features
  • Overall Dimensions: 12"x 7" x 1/2"(thick)
  • Cutout Dimensions: 4.5" x2", Suits most Tower Base
  • Material: Made of non-toxic PVC, safe and anti-corrosion.NO WORRY about rust any more!
  • A Soft PVC Drip Tray Will Definitely be a good helper for your home brewing equipment.
  • Lay flat on counter top.

 

12×7 inches PVC Drip Tray for Home Brewing, Kegerator (Black) – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Continue reading

BN-LINK Digital Cooling Thermostat Controller [Fermentation or Kegerator]

BN-LINK Digital Cooling Thermostat Controller for Cooling Device Circulation Box Fans 40-108F 8.3A 1000W

BN-LINK Digital Cooling Thermostat Controller for Cooling Device Circulation Box Fans 40-108F 8.3A 1000W

More Info

From the product description, check product page for current description, price and availability:

  • ✓ EFFORTLESS COOLING SETUP: Simply place the probe, plug-in the thermostat controller, and use the large 3-button interface to choose your desired temperature setting. Digital display supports units in both Fahrenheit and Celsius. Note: the controller is designed to have a 2-3 degree buffering zone before powering on again after reaching set temperature.
  • ✓ EASE OF MIND: Handy LED cooling and power indicator lights allow you to see the controller’s status even in total darkness. Controller features a convenient hanging tab, and a bright, easy-to-read display inside a tough plastic housing.
  • ✓ RUGGED CONSTRUCTION: The cord for the temperature probe and grounded 3-prong plug measure an extended 6-feet in length, designed to suit almost any application you can imagine.
  • ✓ VARIETY OF USES: Our thermostat controller can be used for refrigeration, fermentation, greenhouse fan and more, keeping your various environments in their ideal temperature range.
  • ✓ SAFE & RELIABLE: Our thermostat controller is ETL listed, and rigorously tested for quality control and safety. Conforms to UL Std No. 60730-1, 60730-2-9. Temperature control range is 40-108°F, temperature display range is 32 -140°F. Rated Voltage is 120VAC 60Hz, Max Loading: 8.3A 1000W. Do not immerse controller or probe into water.

 

What are Other’s Saying?   Search this product’s Amazon reviews for “beer” – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

BN-LINK Digital Cooling Thermostat Controller for Cooling Device Circulation Box Fans 40-108F 8.3A 1000W – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Yeast Starters & Fermentation | Kegerator Tips & Gear | Inkbird Dual Stage Temp Controller

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Inkbird ITC-308 Digital Temperature Controller| Review