Category Archives: Pumps

Hands on Review: Northern Brewer Anti-Gravity Transfer Pump + Limited Time DEAL

This review is by Homebrew Finds Contributor Brad Probert.  Brad is an engineer, expert homebrewer and experienced reviewer.  Grab a link to Brad’s website at the end of this review.

Northern Brewer Anti-Gravity Transfer Pump

Some homebrew gear has a wide range of use, and some fills a very specific purpose. Those that fill a specific purpose typically become a critical piece in your process that you wonder how you managed before you had it. For me, that was the Anti-Gravity Transfer Pump from Northern Brewer. This pump is specifically intended for use in transferring beer or wort from vessel to vessel during your fermentation and/or kegging processes.

Closeup of Pump Head

The Anti-Gravity pump is a diaphragm pump, which is different than your typical wort pump. Wort pumps are usually an impeller design with a pump head inside with rotating blades that push little bits of fluid along from the inlet to the outlet as they spin. A diaphragm pump has a flexible membrane inside that oscillates back and forth like a trampoline. When the membrane is pushed in one direction, it compresses the fluid and forces it to the outlet. And when the membrane is pulled in the opposite direction, it creates a vacuum in the pump chamber which draws fluid in. A set of check balls ensures flow only goes in one direction.

Hose Connection on Inlet and Outlet

Limited Time DEAL:

17% Off at AIH! – use coupon code LUCK17

This deal makes this pump $49.79 when you using coupon code LUCK17

Self-priming Anti-Gravity Transfer Pump

Check Prices and Availability, Review Continues Below:

Continue reading →

KegLand TC Breakdown Brewing Pump Head Upgrade Kit – Upgrade Your Kegland MKII Pump – Save 15%

KegLand TC Breakdown Brewing Pump Head | MKII Pump Head Upgrade Kit | Stainless Steel | 3" Tri-Clamp PMP503

KegLand TC Breakdown Brewing Pump Head | MKII Pump Head Upgrade Kit | Stainless Steel | 3″ Tri-Clamp

More Info

From the product description, check product page for current description, price and availability:

  • Upgrade your MKII Magnetic Drive Pump with a stainless steel pump head that quickly & easily installs via 3″ tri-clamp
  • T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees
  • Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use
  • Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy
  • Stainless steel head with 1/2″ threaded ports to attach your preferred fittings—tri-clamp, quick disconnect, camlock, and More!

Upgrade your MKII Magnetic Drive Pump with a stainless steel inline pump head! The TC Breakdown Brewing Pump Head provides several advantages over the standard MKII pump head, first and foremost being it’s made of stainless steel instead of plastic. This allows for much easier installment of fittings without the risk of breaking off the plastic inlet or outlet. It will also convert the pump head from “Center Inlet” to “Inline” flow path which can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. But what some MKII users might find most exciting about this upgrade kit is that it converts the pump head connection to 3″ tri-clamp! Not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use has never been easier—just pop off the tri-clamp, wash out the pump head, and clamp back on.

This upgrade kit is only compatible with the 25-Watt MKII pump (PMP500). It will not fit the larger 65-Watt MKII or the Blichmann Engineering RipTide pump. If you don’t already own the 25-Watt MKII, you can purchase it with the T.C. pump head already installed here.

Tri-Clamp Pump Head
The T.C. pump head can be removed quickly and easily using the 3″ tri-clamp. This means no drivers or power drills are needed to back out the six Phillips head screws that mount the pump head on the standard version of the MKII. Whip the head off in a flash to clear out spent grain, hop material, or clear a blockage. Attaching the pump head with a tri-clamp also allows the head to be rotated at any angle in a full 360-degrees. This makes it easy to configure the plumbing to your unique brewery setup.

Inline Design
An “inline” pump head simply means the input and output are on a straight horizontal line with one another which can make it easier to integrate into your brewery setup. If you’re using a 3-vessel horizontal system, the inline pump head will make it easier to keep your hoses neat and tidy compared to pumps heads with a center inlet.

PRV Purge Valve
The corny keg style PRV will make priming the pump a breeze. Simply let bleed the pump head to purge air out before turning the pump on and you’ll avoid any cavitation issues. The PRV also acts as a safety so you do not over pressurize your pump head or brewery system.

304 Stainless Steel
The entire pump head is made from 304 grade stainless steel so it’s highly resistant to chemicals, heat, and physical abuse. The 1/2″ BSP threaded ports can be used to attach barbs, quick disconnects, camlocks, tri-clamp adapters, or any other 1/2″ fittings you prefer.

KegLand Part Number: KL27267

 

This is an upgrade kit for the Kegland standard model MKII pump

KegLand TC Breakdown Brewing Pump Head | MKII Pump Head Upgrade Kit | Stainless Steel | 3″ Tri-Clamp PMP503

[/expand]

Save 15%!  (this ends 2/29)

morebeer.com sale

  • MoreBeer offering 15% off most things site wide!
  • *Code will not work with other coupon codes. Offer not valid on gift cards, items over $1000 or products already on sale & MAP products which have an indication on their product page. Single use per customer.
  • Get Free Shipping: This ships for free with a qualify order as part of MoreBeer’s Free Shipping Program.  Under that promo most orders over $59 ship for free.

MoreBeer Leap Beer Sale!

Also Consider:

15% Off Kegland’s New 65 Watt Pump! + See it in action

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. tag:b3peroff

15% Off Kegland’s New 65 Watt Pump! + See it in action

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt from MoreBeer

More Info

From the product description, check product page for current description, price and availability:

The “Big Brother” to one of our best-selling pumps! Expect the same quality that customers have come to expect from the MKII Pump (PMP500) but with more power. This 65 watt magnetic drive pump is powerful enough for homebrewers and micro brewers alike. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The pump head is made from 304 grade stainless steel with 3/4″ threaded ports that can easily be converted to tri-clamp. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self-priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orientations.

We recommend adding two 1.5″ T.C. x 3/4″ Female BSPP adapters to the ports. From there you can use a ForgeFit 1.5″ T.C. x Male QD to use quick disconnects with your lines, or convert to your preferred tri-clamp fittings.

Features:

110V / 60hz
Max Head: 15-21 ft.
Max Flow: 13.5 Gal/min
Max Temp: 248°F (120°C)
Rotatable 304 stainless steel pump head
3/4″ BSPT fittings
Water resistant casing

 

Save 15%!

morebeer.com sale

  • MoreBeer offering 15% off most things site wide!
  • *Code will not work with other coupon codes. Offer not valid on gift cards, items over $1000 or products already on sale & MAP products which have an indication on their product page. Single use per customer.
  • Get Free Shipping: This ships for free with a qualify order as part of MoreBeer’s Free Shipping Program.  Under that promo most orders over $59 ship for free.

MoreBeer Leap Beer Sale!

This works with Kegland’s 65 watt pump!

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt PMP502

Also:

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. rpu:b3pumpbattle tag:b3peroff tag:watch

Pedal Foot Switch [Pump Operation and More)

FarBoat Foot Switch Foot Operated Pedal Controller ON/Off Power Switch

FarBoat Foot Switch Foot Operated Pedal Controller ON/Off Power Switch

More Info


Highlighted Features
  • Product Name: foot switch. Learn more detail information in Product Description, please! FarBoat provides different types of electronic tools, and there is always one for you!
  • [Sizes] Overall size: 100×61×36mm/3.9"×2.4"×1.4"(L×W×H). Length of cable: 135mm/5.3"(Approx.).
  • Current: 10A. Voltage: AC 380V. Ingress protection: IP62. Conform to IEC337-1.
  • Inflaming retarding outer layer, quick response.
  • [Measurement Difference] There may be 1-3mm difference in size due to the manual measurement, please notice and thank you for your understanding.
Learn More

 

I use an on/off foot pedal foot switch (different model, manufacturer and specs) for hands free control of my March Pump while brewing. Other possible applications could be to control a keg washer or draft line cleaning pump.

Always use caution when using your pump with hot liquids.  Likewise use caution when using electricity around liquids.  Hot liquids and electricity can be dangerous.  Always read and follow manufacturer directions.

FarBoat Foot Switch Foot Operated Pedal Controller ON/Off Power Switch Woodworking and Sewing Machine AC380V 10A – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: Build A Recirculating Draft Line Cleaning Pump | Hands On Review: Mark’s Keg and Carboy Washer

Using a Pedal Foot Switch for Easy Pump Operation

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Make sure the components you use are compatible and rated for your intended application.  Contact manufacturer with questions about suitability or a specific application.  Always read and follow manufacturer directions.

Magnetic Drive Homebrew Pump w/Stainless Steel Head

Magnetic Drive Home Brew Beer Siphon and Water Circulation Pump - Stainless Steel Head with 1/2in Thread

Magnetic drive homebrew pump

More Info

From the product description, check product page for current description, price and availability:

  • [Safely Transfer Liquids]: Use the G. Francis Magnetic Drive Home Brew Beer Siphon and Water Circulation Pump to transfer hot and cold liquids instead of trying to move giant brew kettles yourself and running into accidents and injuries; Transferring liquids is a part of any homebrew operation, and this magnetic drive pump is an optimum liquid transport pump with high output volume and quiet operation for industrial and home equipment
  • [Easy to Use]: Prime by running liquid through pump prior to turning on; The liquid travels from the bottom of the valve into the pump, and once device is powered on (plugged in to outlet), the propeller circulates liquid for maximum flow; Use to dispense beer, treat water, transfer hot water from your kettle to a mash tun, or recirculate mash wort and sparge and transfer to a brew kettle
  • [Built to Last]: Stainless-steel head, magnetic pump, plastic head for strength and longevity; Safe for beverages, resistant to abrasion, corrosion, and heat up to 221 degrees Fahrenheit (105 degrees Celsius); 6.5-inch x 2.6-inch (15.5cm x 6.4cm) pump overall dimensions with 3.25-inch x 2.5-inch (8.3cm x 6.4cm) steel mounting plate (mounting hardware not included)
  • [Magnetic]: Fully sealed pump motor with connecting magnetic shaft and magnetic propeller; Magnetically coupled for enhanced operation
  • [Specifications]: 4.75-foot (1.4m) long 3-prong 18AWG power cord; 1/2-inch NPT thread; 110V; Not self-priming (do not run dry); 5 gallons per minute (19 L/min) maximum capacity; 11.2-foot (3.4m) maximum head; 10W rated power; 150mA current; 60 Hz frequency; 3,000 r/min speed

 

I use my homebrew pump (different model and different manufacturer) for vorlaufing/recirculating, transferring from my mash tun to brew kettle, chilling with a recirculating wort chiller and transferring to my fermenter.

Magnetic Drive Home Brew Beer Siphon and Water Circulation Pump – Stainless Steel Head with 1/2in Thread – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

amazon

Hands on Review: Mark II Homebrew Pump w/Stainless Head + 30% Off Coupon!

This review is by Homebrew Finds Contributor Brad Probert.  Brad is an engineer, expert homebrewer and experienced reviewer.  Grab a link to Brad’s website at the end of this review.

Mark II Pump with Steel Head

Let’s face it, pumps aren’t the most exciting piece of homebrew equipment you own. With the exception of the RipTide pump, they don’t have “features” you can impress your friends with. There are a few basic requirements, and once you get those met, you’re just looking for the lowest price. For me, the basic requirements are: 1) Magnetic drive, 2) Ideally a stainless steel head, 3) Temperature & splash protection, and lastly 4) Maximum head.

The MkII’s Magnetic Impeller

Several vendors offer what’s called a “Mark II Pump”. So you need to dig deeper than just the name when comparing pump offerings from different shops. One requirement, which is pretty much standard across beer brewing pumps, is what’s called a magnetic drive. Magnetic drive means you don’t have to worry about grease from shaft bearings getting into your wort. The other advantage is that you can close a valve- partially or completely- on the output side of your pump to reduce flow, and it causes no stress to your pump. Magnetic drive is pretty much standard in beer brewing pumps, but I bring it up because shopping on Amazon or eBay you might get drawn into something that isn’t.

Check Current Price & Availability:

MARK II BEER PUMP via Proflow Dynamics

Limited Time Deal!

PFD is taking 30% off their homebrew category when you use promo code BF30%. Considering their already, generally, great everyday prices, this is an outstanding deal!

ProFlow’s Homebrew Lineup – remember coupon code BF30% to get an additional 20% off

  • This works with the MK II Pump!
  • Shipping is an additional cost based on your location.  Because of minimum shipping costs, it may make sense to place a larger order.  Additional items may ship for minimal cost.

MK II Brewing Pump – remember coupon code BF30%

About Pump Features and Specs – What does Pump Head Mean?

Pump heads come in either stainless steel or some kind of plastic/resin. Some resins have a better temperature durability, so after many hours of operation they are less likely to break down and lose pressure/flow capability. Stainless steel doesn’t have this issue, but it also has more durable threads. Most wort pumps come with 1/2″ Male NPT at inlet and outlet so you can screw on hose attachments or ball valves. I’ve had bad luck with stripping threads off a polysulphone pump head even with the most careful attention paid to not cross-threading it.

The next key differentiator between pumps is temperature capability. Some are designed to handle cooler liquids and are maybe only rated to something like 80F or 180F. This simply isn’t good enough for brewing, you want something that can handle boiling wort temperatures (212F or hotter).

Continue reading →

20% Off Kegland’s New 65 Watt Pump!

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt from MoreBeer

More Info

From the product description, check product page for current description, price and availability:

The “Big Brother” to one of our best-selling pumps! Expect the same quality that customers have come to expect from the MKII Pump (PMP500) but with more power. This 65 watt magnetic drive pump is powerful enough for homebrewers and micro brewers alike. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The pump head is made from 304 grade stainless steel with 3/4″ threaded ports that can easily be converted to tri-clamp. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self-priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orientations.

We recommend adding two 1.5″ T.C. x 3/4″ Female BSPP adapters to the ports. From there you can use a ForgeFit 1.5″ T.C. x Male QD to use quick disconnects with your lines, or convert to your preferred tri-clamp fittings.

Features:

110V / 60hz
Max Head: 15-21 ft.
Max Flow: 13.5 Gal/min
Max Temp: 248°F (120°C)
Rotatable 304 stainless steel pump head
3/4″ BSPT fittings
Water resistant casing

 

20% Off, TWO Coupons to Choose from

  • MoreBeer offering 20% off a single item when you use coupon code TOP5
  • *Code will not work with other coupon codes. Offer not valid on gift cards, items over $1000 or products already on sale & MAP products which have an indication on their product page. Single use per customer. Valid through 1/31
  • Get Free Shipping: This ships for free with a qualify order as part of MoreBeer’s Free Shipping Program.  Under that promo most orders over $59 ship for free.

20% Off at MoreBeer!  use coupon code TOP5

OR… If you’ve used that coupon coupon code MYPICK also takes 20% off a single item – valid through 1/28.

This works with Kegland’s 65 watt pump!

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt PMP502

Also:

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. rpu:b3pumpbattle tag:b3peroff

KegLand MKII Brewing Pump w/Stainless Steel Head! – BACK in Stock! + Save 20%!

KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt PMP504

KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt

From the product description, check product page for current description, price and availability:

  • Magnetic drive enables you to slow down the flow without damaging the pump—just add a ball valve to the outlet!
  • T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees
  • Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use
  • Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy
  • Stainless steel head with 1/2″ threaded ports to attach your preferred fittings—tri-clamp, quick disconnect, camlock, and More!

The best-selling MKII Magnetic Drive Pump now available with a major upgrade! This unit comes standard with an inline stainless steel pump head that installs on the pump body with a 3″ tri-clamp. Compared to the standard “center inlet” pump head, the “inline” flow path can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. And with the 3″ T.C. connection, not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use could not be easier—just pop off the tri-clamp, wash out the pump head, and clamp back on.

Continue reading →

Announcing: KegLand Tri-Clamp Pump w/Stainless Steel Head!

 

KegLand MKII Magnetic Drive Pump | Tri-Clamp Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt PMP505

KegLand MKII Magnetic Drive Pump | Tri-Clamp Inline Pump Head

More Info

From the product description, check product page for current description, price and availability:

  • Magnetic drive enables you to slow down the flow without damaging the pump—just add a ball valve to the outlet!
  • T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees
  • Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use
  • Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy
  • Stainless steel head with 1.5″ T.C. ports to attach your preferred tri-clamp fittings

The best-selling MKII Magnetic Drive Pump now available with a major upgrade! This unit comes standard with an inline stainless steel pump head that installs on the pump body with a 3″ tri-clamp. Compared to the standard “center inlet” pump head, the “inline” flow path can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. And with the 3″ T.C. connection, not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use could not be easier—just pop off the tri-clamp, wash out the pump head, and clamp back on.

The MKII is a perfect pump for your system and comes highly recommended for brewers stepping up to all-grain brewing. Rather than schlepping heavy kettles filled with hot liquor or wort around your brewery, or awkwardly stacking them into a 3-tier gravity setup, allow this handy pump to move liquid from vessel to vessel while everything remains in place. The magnetic drive allows you to slow down the flow without damaging the pump. This can be done by attaching a ball valve to the outlet side of the pump, and then you simply open or close the valve to control the flow rate. The pump itself is not self-priming, but priming is super easy thanks to the pull ring PRV which will help ensure the pump head is full of liquid and trapped air is released before powering it on.

Tri-Clamp Pump Head
The T.C. pump head can be removed quickly and easily using the 3″ tri-clamp. This means no drivers or power drills are needed to back out the six Phillips head screws that mount the pump head on the standard version of the MKII. Whip the head off in a flash to clear out spent grain, hop material, or clear a blockage. Attaching the pump head with a tri-clamp also allows the head to be rotated at any angle in a full 360-degrees. This makes it easy to configure the plumbing to your unique brewery setup.

Inline Design
An “inline” pump head simply means the input and output are on a straight horizontal line with one another which can make it easier to integrate into your brewery setup. If you’re using a 3-vessel horizontal system, the inline pump head will make it easier to keep your hoses neat and tidy compared to pumps heads with a center inlet.

PRV Purge Valve
The corny keg style PRV will make priming the pump a breeze. Simply let bleed the pump head to purge air out before turning the pump on and you’ll avoid any cavitation issues. The PRV also acts as a safety so you do not over pressurize your pump head or brewery system.

304 Stainless Steel
The entire pump head is made from 304 grade stainless steel so it’s highly resistant to chemicals, heat, and physical abuse. The 1/2″ BSP threaded ports can be used to attach barbs, quick disconnects, camlocks, tri-clamp adapters, or any other 1/2″ fittings you prefer.

Features:

  • 110V / 60hz
  • Max Head: 11.15 ft. (3.4 m)
  • Max Flow: 5 Gal/min (19L/min)
  • Max Temperature: 248°F (120°C)
  • 360° rotatable stainless steel pump head
  • 1.5″ T.C. ports
  • Water resistant casing (not waterproof)

KegLand Part Number: KL27526

If you’re brewing on a budget and want the most affordable pump possible, check out the standard model MKII pump. This has been our best-selling pump for years and you can always upgrade it down the road with the standard stainless center inlet head or inline stainless tri-clamp head.

 

KegLand MKII Magnetic Drive Pump | Tri-Clamp Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt PMP505

Also: KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt PMP504

Price, promotions and availability can change quickly. Check the product page for current price, description and availability  tag:b3peroff

Save on Recently Released KegLand TC Breakdown Tri Clamp Pump at William’s Brewing!

KegLand TC Breakdown Tri Clamp Pump

KegLand TC Breakdown Tri Clamp Pump from William’s Brewing

More Info

From the product description, check product page for current description, price and availability:

The KegLand TC Breakdown pump features a type 304 stainless head held on with a 3” Tri Clamp, making it easy to service and remove any spent grain or hop material that may cause a blockage. It features an inline design with 1.5″ Tri Clamp in and out fittings. The Tri Clamp head allows the head to be set at any angle, making it even easier to integrate into your system.

A corny keg compatible PRV valve with pull ring is screwed into the head so you can quickly perge the head to eliminate cavitation, and also acts as a safety valve so you cannot over pressurize your system. Best of all, you can replace it if needed with any corny compatible relief valve.

This 25 watt pump runs on 110 volts, and will pump up to 5 gallons per minute to a height of 11 feet. This performance is based on minimal lift, and keep in mind the higher you pump, the less gallons per minute.

 

  • For limited time William’s Brewing has this on sale for $149.99. That’s a $30 savings.
  • No coupon code required, check product page for availability.
  • Shipping is free or reasonably priced flat rate to addresses in the contiguous US depending on your order size for most items.

KegLand TC Breakdown Tri Clamp Pump

Video on Product Page…

KegLand TC Breakdown Tri Clamp Pump

This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

Visit William’s Brewing – Web Only Clearance Sale

williams

Price, promotions and availability can change quickly. Check the product page for current price, description and availability.

KegLand MKII Brewing Pump w/Stainless Steel Head! – BACK in Stock! + Save 20%!

KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt PMP504

KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt

From the product description, check product page for current description, price and availability:

  • Magnetic drive enables you to slow down the flow without damaging the pump—just add a ball valve to the outlet!
  • T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees
  • Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use
  • Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy
  • Stainless steel head with 1/2″ threaded ports to attach your preferred fittings—tri-clamp, quick disconnect, camlock, and More!

The best-selling MKII Magnetic Drive Pump now available with a major upgrade! This unit comes standard with an inline stainless steel pump head that installs on the pump body with a 3″ tri-clamp. Compared to the standard “center inlet” pump head, the “inline” flow path can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. And with the 3″ T.C. connection, not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use could not be easier—just pop off the tri-clamp, wash out the pump head, and clamp back on.

Continue reading →

TWO Deals on MKII High Temp Magnetic Drive Pump! – one time coupon or DOD

MKII High Temp Magnetic Drive Pump

MKII High Temp Magnetic Drive Pump from MoreBeer

More Info

From the product description, check product page for current description, price and availability:

This magnetic drive pump is a perfect pump for your brew system. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The housing of the unit is made from tough, food grade polysulfone. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orienations. An optional stainless head, PMP501, can also be purchased.

Features:

110v/60hz
Max Head: 11.15 ft. (3.4 m)
Max Flow: 5 Gal/min (19L/min)
1/2 inch fittings
Rotatable pump head
Max temperature – 248 F/ 120 C
Water resistant (not proof!) casing

 

MKII High Temp Magnetic Drive Pump PMP500

20% Off a Single Item at MoreBeer = $63.99

  • MoreBeer is taking 20% off a single item when you use coupon code TOP5
  • *Code will not work with other coupon codes. Offer not valid on gift cards, items over $1000 or products already on sale & MAP products which have an indication on their product page. Single use per customer.

20% Off at MoreBeer!  use coupon code TOP5

Coupon code TOP5 makes this popular pump just $63.99 and shipping is free to many US addresses.

OR, If you’ve already used the one time coupon $64.99 via Deal of the Day…

Deal of the Day 1/12/24

Limited Availability Deal of the Day: As of this posting, this on sale for $64.99 as as a MoreBeer Deal of the Day. Shipping is also free to addresses in the contiguous US with most $59 Orders. Availability: This is available today only, while supplies last. Quantities are limited. Check the MoreBeer’s Deal of the Day to check today’s offering.

Product Description – Here – Use coupon code BEERDEAL to get this discount.

MKII High Temp Magnetic Drive Pump PMP500

Also:

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability  tag:b3peroff ssprd:PMP500:ptr

$45 Off Chugger X-Dry Series Tri-Clamp Center Inlet Homebrew Pump!

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) - Stainless Steel H336

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) via MoreBeer

More Info

From the product description, check product page for current description, price and availability:

Introducing the X-Dry Series Chugger Pumps! These pumps offer the same great quality we’ve come to expect from Chugger, but now feature Run-Dry Protection. Although the Chugger still needs to be primed before each use, the X-Dry Series offers a new level of protection from damage due to cavitation.

The Chugger lineup of pumps represents a great value for an even better price. These pumps are workhorses in the brewery. Featuring a robust flow rate of 7 gpm, and a magnetic drive designed to handle back-pressure, these pumps are a great addition to any brewing setup! The Stainless Steel Chugger showcases their molded Stainless Steel Pump Head. This stainless pump is a steal for the price, and we’ve been more than happy with the quality! Use this to ease transfers between kettles, cool wort via a counterflow chiller, or recirculate icewater for quicker chilling!

The Chugger pump model has 1.5″ tri-clamp inlet and outlet, allowing easy integration with your T.C. kettles or fermenter! We recommend setting these pumps up with a butterfly valve on the outflow side, this way you can throttle down the outgoing flow rate, allowing for more efficient sparges or cooling! The pump head can also be rotated 360° (in 90° intervals) allowing for even more customization!

Features:

Run Dry Carbon Bearing
Stainless Steel Center Inlet Pump Head
Food Grade up to 250° F
1.5″ tri-clamp inlet and outlet
High Flow rate of 7 gpm
Max Head 18.6 ft
115v 55″ cord and plug attached
50/60 Hz, 1.4 amp
1/20 HP, 3500 RPM
Note: When using silicone tubing, we recommend using a slighlty larger barb than the I.D. of the tubing. This is because silicone tubing tends to have greater pliability than most tubing. For example, when using 1/2″ silicone tubing, we recommend our 5/8″ barb (H620), to help ensure a better seal!

 

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) – Stainless Steel H336

$45 (or More) Off!

morebeer.com dealAs of this posting, MoreBeer is discounting most things, sitewide by up to $65 based on your order size when you use coupon code SAVEMORE.  Some exclusions apply.  Most items bundle with MoreBeer’s Free Shipping.  Under that promo most orders over $59 ship for free.

Grab the complete details and grab the coupon code  – Brew More Save More at MoreBeer!

This pump qualifies for $45 off when you use coupon code SAVEMORE. Put together a larger order to save $65

Related: Hands on Review: Chugger Pumps X-Dry Series Homebrew Pump!

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. tag:b3brewmore tag:b3peroff tag:b3brewmore

KegLand MKII Brewing Pump w/Stainless Steel Head! – Available Again for Pre-Order + SAVE 20%

KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt PMP504

KegLand MKII Magnetic Drive Pump | Inline Pump Head | Stainless Steel | 5 GPM | 25 Watt

From the product description, check product page for current description, price and availability:

  • Magnetic drive enables you to slow down the flow without damaging the pump—just add a ball valve to the outlet!
  • T.C. connection allows the pump head to be oriented at any angle in a full 360-degrees
  • Pull ring PRV at the pump outlet makes it easy to purge air and prime the pump before each use
  • Inline flow path for smooth integration into your brewery while keeping your tubing lines tidy
  • Stainless steel head with 1/2″ threaded ports to attach your preferred fittings—tri-clamp, quick disconnect, camlock, and More!

The best-selling MKII Magnetic Drive Pump now available with a major upgrade! This unit comes standard with an inline stainless steel pump head that installs on the pump body with a 3″ tri-clamp. Compared to the standard “center inlet” pump head, the “inline” flow path can make it much easier to integrate into your brewery and keep your brewing hoses tidy. At the outlet of the pump, there is a very handy pull ring PRV that allows you to bleed liquor or wort from the pump head to release trapped air and prime the pump. And with the 3″ T.C. connection, not only do you have a full 360-degrees to orient the pump head any which way, cleaning the pump after use could not be easier—just pop off the tri-clamp, wash out the pump head, and clamp back on.

Continue reading →

$45 Off Chugger X-Dry Series Tri-Clamp Center Inlet Homebrew Pump!

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) - Stainless Steel H336

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) via MoreBeer

More Info

From the product description, check product page for current description, price and availability:

Introducing the X-Dry Series Chugger Pumps! These pumps offer the same great quality we’ve come to expect from Chugger, but now feature Run-Dry Protection. Although the Chugger still needs to be primed before each use, the X-Dry Series offers a new level of protection from damage due to cavitation.

The Chugger lineup of pumps represents a great value for an even better price. These pumps are workhorses in the brewery. Featuring a robust flow rate of 7 gpm, and a magnetic drive designed to handle back-pressure, these pumps are a great addition to any brewing setup! The Stainless Steel Chugger showcases their molded Stainless Steel Pump Head. This stainless pump is a steal for the price, and we’ve been more than happy with the quality! Use this to ease transfers between kettles, cool wort via a counterflow chiller, or recirculate icewater for quicker chilling!

The Chugger pump model has 1.5″ tri-clamp inlet and outlet, allowing easy integration with your T.C. kettles or fermenter! We recommend setting these pumps up with a butterfly valve on the outflow side, this way you can throttle down the outgoing flow rate, allowing for more efficient sparges or cooling! The pump head can also be rotated 360° (in 90° intervals) allowing for even more customization!

Features:

Run Dry Carbon Bearing
Stainless Steel Center Inlet Pump Head
Food Grade up to 250° F
1.5″ tri-clamp inlet and outlet
High Flow rate of 7 gpm
Max Head 18.6 ft
115v 55″ cord and plug attached
50/60 Hz, 1.4 amp
1/20 HP, 3500 RPM
Note: When using silicone tubing, we recommend using a slighlty larger barb than the I.D. of the tubing. This is because silicone tubing tends to have greater pliability than most tubing. For example, when using 1/2″ silicone tubing, we recommend our 5/8″ barb (H620), to help ensure a better seal!

 

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) – Stainless Steel H336

$45 (or More) Off!

morebeer.com dealAs of this posting, MoreBeer is discounting most things, sitewide by up to $65 based on your order size when you use coupon code SAVEMORE.  Some exclusions apply.  Most items bundle with MoreBeer’s Free Shipping.  Under that promo most orders over $59 ship for free.

Grab the complete details and grab the coupon code  – Brew More Save More at MoreBeer!

This pump qualifies for $45 off when you use coupon code SAVEMORE. Put together a larger order to save $65

Related: Hands on Review: Chugger Pumps X-Dry Series Homebrew Pump!

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. tag:b3brewmore tag:b3peroff tag:b3brewmore

Ends Today: 20% Off Chugger X-Dry Series Tri-Clamp Center Inlet Homebrew Pump

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) - Stainless Steel H336

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) via MoreBeer

More Info

From the product description, check product page for current description, price and availability:

Introducing the X-Dry Series Chugger Pumps! These pumps offer the same great quality we’ve come to expect from Chugger, but now feature Run-Dry Protection. Although the Chugger still needs to be primed before each use, the X-Dry Series offers a new level of protection from damage due to cavitation.

The Chugger lineup of pumps represents a great value for an even better price. These pumps are workhorses in the brewery. Featuring a robust flow rate of 7 gpm, and a magnetic drive designed to handle back-pressure, these pumps are a great addition to any brewing setup! The Stainless Steel Chugger showcases their molded Stainless Steel Pump Head. This stainless pump is a steal for the price, and we’ve been more than happy with the quality! Use this to ease transfers between kettles, cool wort via a counterflow chiller, or recirculate icewater for quicker chilling!

The Chugger pump model has 1.5″ tri-clamp inlet and outlet, allowing easy integration with your T.C. kettles or fermenter! We recommend setting these pumps up with a butterfly valve on the outflow side, this way you can throttle down the outgoing flow rate, allowing for more efficient sparges or cooling! The pump head can also be rotated 360° (in 90° intervals) allowing for even more customization!

Features:

Run Dry Carbon Bearing
Stainless Steel Center Inlet Pump Head
Food Grade up to 250° F
1.5″ tri-clamp inlet and outlet
High Flow rate of 7 gpm
Max Head 18.6 ft
115v 55″ cord and plug attached
50/60 Hz, 1.4 amp
1/20 HP, 3500 RPM
Note: When using silicone tubing, we recommend using a slighlty larger barb than the I.D. of the tubing. This is because silicone tubing tends to have greater pliability than most tubing. For example, when using 1/2″ silicone tubing, we recommend our 5/8″ barb (H620), to help ensure a better seal!

 

X-Dry Series Tri-Clamp Chugger Pump (Center Inlet) – Stainless Steel H336

Limited Time Deal… 20% Off a Single Item at MoreBeer!

  • MoreBeer is discounting a single item by 20% when you use coupon code GIFT4ME.
  • Get Free Shipping: This ships for free with a qualify order as part of MoreBeer’s Free Shipping Program.  Under that promo most orders over $59 ship for free.

20% Off at MoreBeer!  use coupon code GIFT4ME

Double dip… place multiple orders to get on this more than once.

Related: Hands on Review: Chugger Pumps X-Dry Series Homebrew Pump!

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. tag:b3brewmore tag:b3peroff tag:watchan Announcing: Chugger X-Dry Series Tri-Clamp Center Inlet Homebrew Pump 1.25.23

Beer Pump Battle! See Kegland’s New 65 Watt Pump In Action

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt from MoreBeer

More Info

From the product description, check product page for current description, price and availability:

The “Big Brother” to one of our best-selling pumps! Expect the same quality that customers have come to expect from the MKII Pump (PMP500) but with more power. This 65 watt magnetic drive pump is powerful enough for homebrewers and micro brewers alike. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The pump head is made from 304 grade stainless steel with 3/4″ threaded ports that can easily be converted to tri-clamp. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self-priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orientations.

We recommend adding two 1.5″ T.C. x 3/4″ Female BSPP adapters to the ports. From there you can use a ForgeFit 1.5″ T.C. x Male QD to use quick disconnects with your lines, or convert to your preferred tri-clamp fittings.

Features:

110V / 60hz
Max Head: 15-21 ft.
Max Flow: 13.5 Gal/min
Max Temp: 248°F (120°C)
Rotatable 304 stainless steel pump head
3/4″ BSPT fittings
Water resistant casing

 

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt PMP502

Also:

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. rpu:b3pumpbattle tag:b3peroff

Beer Pump Battle! See Kegland’s New 65 Watt Pump In Action

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt from MoreBeer

More Info

From the product description, check product page for current description, price and availability:

The “Big Brother” to one of our best-selling pumps! Expect the same quality that customers have come to expect from the MKII Pump (PMP500) but with more power. This 65 watt magnetic drive pump is powerful enough for homebrewers and micro brewers alike. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The pump head is made from 304 grade stainless steel with 3/4″ threaded ports that can easily be converted to tri-clamp. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self-priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orientations.

We recommend adding two 1.5″ T.C. x 3/4″ Female BSPP adapters to the ports. From there you can use a ForgeFit 1.5″ T.C. x Male QD to use quick disconnects with your lines, or convert to your preferred tri-clamp fittings.

Features:

110V / 60hz
Max Head: 15-21 ft.
Max Flow: 13.5 Gal/min
Max Temp: 248°F (120°C)
Rotatable 304 stainless steel pump head
3/4″ BSPT fittings
Water resistant casing

 

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt PMP502

https://www.youtube.com/watch?v=CYP7CRupcUk

Also:

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. rpu:b3pumpbattle tag:b3peroff

Beer Pump Battle! See Kegland’s New 65 Watt Pump In Action

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt from MoreBeer

More Info

From the product description, check product page for current description, price and availability:

The “Big Brother” to one of our best-selling pumps! Expect the same quality that customers have come to expect from the MKII Pump (PMP500) but with more power. This 65 watt magnetic drive pump is powerful enough for homebrewers and micro brewers alike. Use it to move hot wort in an all-grain system and also to transfer wort from boil kettle to fermenter. The pump head is made from 304 grade stainless steel with 3/4″ threaded ports that can easily be converted to tri-clamp. The magnetic drive allows you to slow down the flow without damaging the pump. This pump is not self-priming so do not run the pump dry. The pump head can be rotated in 60-degree increments, allowing for 6 different pump head orientations.

We recommend adding two 1.5″ T.C. x 3/4″ Female BSPP adapters to the ports. From there you can use a ForgeFit 1.5″ T.C. x Male QD to use quick disconnects with your lines, or convert to your preferred tri-clamp fittings.

Features:

110V / 60hz
Max Head: 15-21 ft.
Max Flow: 13.5 Gal/min
Max Temp: 248°F (120°C)
Rotatable 304 stainless steel pump head
3/4″ BSPT fittings
Water resistant casing

 

KegLand MKII Magnetic Drive Pump | Center Inlet Pump Head | Stainless Steel | 13.5 GPM | 65 Watt PMP502

Also:

pinned

This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

morebeer

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. rpu:b3pumpbattle tag:b3peroff

Mark II 25 Watt Wort Pump – on sale for… $39.99 at William’s Brewing

Mark II 25 Watt Wort Pump

Mark II 25 Watt Wort Pump from William’s Brewing

More Info

From the product description, check product page for current description, price and availability:

The MKII Pump from Keg Land is a magnetic drive high temperature pump capable of pumping hot wort at temperatures of up to 248° F. It can pump up to 5 gallons per minute, making it perfect for 5 to 20 gallon systems. The maximum height it can pump is 11’ although gallons per minute will be reduced at higher pumping elevations.

The pump head and impeller are constructed of food grade Xarec plastic (very similar to Polysulphone). The magnetic drive acts as a clutch allowing the user to put back pressure on the pump to slow down flow. Like all magnetic drive wort pumps, it is not self priming – you must flood the pump head before turning on the pump. The pump has ½” BSP male fittings on the inlet and outlet, which are compatible with all our ½” female NPT fittings. The inlet is in the center. Besides Xarec plastic, other wetted interior materials are nitrile rubber and stainless steel.

The magnetic drive ensures no lubricated bearings are in contact with the liquid at all, so you can be sure there is no chance of any contamination of the liquid being pumped. The pump features a 67” power cord, and a mounting plate for permanent mounting. The pump is 7¾” in overall length, and 3¼” wide including the mounting plate. The polysulfone head can be mounted at any angle on the pump to fit your application (an optional stainless head, William’s item Q80, is also available). Shop around and compare, we think this is the best value currently available in a high temperature wort transfer pump.

Important Safety Notice: This pump, like all 110 volt items that run in potentially wet areas, should be plugged into a GFI protected outlet for safety.

 

Mark II 25 Watt Wort Pump – William’s Brewing Big Holiday Sale

Stainless Steel Head Upgrade

Also at William’s Brewing: Mark II 65 Watt Wort Pump

This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!

pinned

Visit William’s Brewing – Web Only Clearance Sale

williams

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. tag:wmsmii25pump