This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
From the product description, check product page for current description, price and availability:
The MKII Pump from Keg Land is a magnetic drive high temperature pump capable of pumping hot wort at temperatures of up to 248° F. It can pump up to 5 gallons per minute, making it perfect for 5 to 20 gallon systems. The maximum height it can pump is 11’ although gallons per minute will be reduced at higher pumping elevations.
The pump head and impeller are constructed of food grade Xarec plastic (very similar to Polysulphone). The magnetic drive acts as a clutch allowing the user to put back pressure on the pump to slow down flow. Like all magnetic drive wort pumps, it is not self priming – you must flood the pump head before turning on the pump. The pump has ½” BSP male fittings on the inlet and outlet, which are compatible with all our ½” female NPT fittings. The inlet is in the center. Besides Xarec plastic, other wetted interior materials are nitrile rubber and stainless steel.
The magnetic drive ensures no lubricated bearings are in contact with the liquid at all, so you can be sure there is no chance of any contamination of the liquid being pumped. The pump features a 67” power cord, and a mounting plate for permanent mounting. The pump is 7¾” in overall length, and 3¼” wide including the mounting plate. The polysulfone head can be mounted at any angle on the pump to fit your application (an optional stainless head, William’s item Q80, is also available). Shop around and compare, we think this is the best value currently available in a high temperature wort transfer pump.
Important Safety Notice: This pump, like all 110 volt items that run in potentially wet areas, should be plugged into a GFI protected outlet for safety.
Check sale or product page for current availability & pricing
This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
…. and more – wort chillers, site glasses, pickup tubes, false bottoms and more
Mark II Beer Pump via Proflow Dynamics
More Info
From the product description, check product page for current description, price and availability:
MK II High Temperature Magnetic Drive Pump
Stainless Steel Head
110V/60HZ
3.4 meter max head
5 GPM (19L max flow)
Max temperature 248 F/ 120 C
Water resistant casing
25 Watt Wort Pump
1/2 inch fittings
The MK 11 Magnetic Drive Pump is constructed using food-grade materials and handles boiling wort with ease. The magnetic drive functions like a clutch allowing one to slow the flow rate down by putting back pressure on the pump. Since it is centrifugal, it’s not self priming, you must put the pump under the level of the liquid source. This magnetic driven pump allows you to brew with confidence knowing that no contamination will occur from lubricated bearing potentially coming into contact with your liquid (beer).
As of this posting, PFD has this for $99.99.
10% Off! Promo code BREW15% gets you 10% off PFD’s entire homebrew lineup
ANOTHER 10% Off: You get another 10% off by using any of the links in this post. Discount reflected at checkout
The stacking deals make this pump $76.49.
Shipping is an additional cost based on your location. Because of minimum shipping costs, it may make sense to place a larger order. Additional items may ship for minimal cost.
MK II Brewing Pump – remember coupon code BREW15% + any link in this post for ANOTHER 10% off
pinned
This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
greatdeals
Price, promotions and availability can change quickly. Check the product page for current price, description and availability prod:pfdmkii
From the product description, check product page for current description, price and availability:
[Safely Transfer Liquids]: Use the G. Francis Magnetic Drive Home Brew Beer Siphon and Water Circulation Pump to transfer hot and cold liquids instead of trying to move giant brew kettles yourself and running into accidents and injuries; Transferring liquids is a part of any homebrew operation, and this magnetic drive pump is an optimum liquid transport pump with high output volume and quiet operation for industrial and home equipment
[Easy to Use]: Prime by running liquid through pump prior to turning on; The liquid travels from the bottom of the valve into the pump, and once device is powered on (plugged in to outlet), the propeller circulates liquid for maximum flow; Use to dispense beer, treat water, transfer hot water from your kettle to a mash tun, or recirculate mash wort and sparge and transfer to a brew kettle
[Built to Last]: Stainless-steel head, magnetic pump, plastic head for strength and longevity; Safe for beverages, resistant to abrasion, corrosion, and heat up to 221 degrees Fahrenheit (105 degrees Celsius); 6.5-inch x 2.6-inch (15.5cm x 6.4cm) pump overall dimensions with 3.25-inch x 2.5-inch (8.3cm x 6.4cm) steel mounting plate (mounting hardware not included)
[Magnetic]: Fully sealed pump motor with connecting magnetic shaft and magnetic propeller; Magnetically coupled for enhanced operation
[Specifications]: 4.75-foot (1.4m) long 3-prong 18AWG power cord; 1/2-inch NPT thread; 110V; Not self-priming (do not run dry); 5 gallons per minute (19 L/min) maximum capacity; 11.2-foot (3.4m) maximum head; 10W rated power; 150mA current; 60 Hz frequency; 3,000 r/min speed
I use my homebrew pump (different model and different manufacturer) for vorlaufing/recirculating, transferring from my mash tun to brew kettle, chilling with a recirculating wort chiller and transferring to my fermenter.
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
From the product description, check product page for current description, price and availability:
The ultimate pump for home winemaking use. Self-priming (will push air) so that it can draw out of a tank. Gentle diaphram action so as to not “beat up” the wine. Made of food-grade, NSF approved, materials polypropylene and santoprene, so no metallic interaction with wine. Pumps 3 gallons per minute. Flow can be restricted with an inline valve positioned on the outflow side. Self-regulating motor is designed to temporarily shut down, and then turn back on, when restriction pressure exceeds pump capacity. Has a heat limitation of 125 degrees Fahrenheit so cannot be used in brewing applications.
Pump is equipped with 1/2″ Male NPT posts on the inlet and outlet. Does not include the plastic barb fittings you will need to purchase separately. Please see the “You Might Also Need” section below for our recommendations regarding which fittings to attach to the pump.
Please Note: The diaphragms in this pump are very sensitive to sediment and particulates and can be damaged if any solids are taken into the pump head. We recommend using an Inline Pre-Filter (FIL26) if you think there’s a risk of sucking up solids with your inlet hose (pumping during pressing, for instance).
Winexpert Vintner’s Reserve Chardonnay Wine Recipe Kit. About: “The perennial white wine favorite. A remarkably versatile wine, this classic now includes oak for a rounded vanilla-oak structure that is smooth and appealing. Dry, with pleasant acidity, Chardonnay’s complexity is fully realized when aged.”
Limited Availability Wine Deal of the Week: As of this posting, this is marked down to $164.99 as a MoreWine Deal of the Week. Shipping is also free to addresses in the contiguous US with most $59 Orders. Quantities are limited. Check the Deal of the Week section – Here – to see if this is still available.
Note that you can redeem this on MoreBeeror MoreWine. Use coupon code WINEDEAL to get this discount.
This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
From the product description, check product page for current description, price and availability:
You likely want to monitor the temperature of your wort as it moves from the chiller to the fermenter, and now you can do just that with this In-Line Thermometer. This high quality thermometer features stainless steel quick disconnects for easy installation in line with the rest of your brewing system, and many users install it on the “out” side of their convoluted heat exchangers and counterflow chillers.
As the wort runs through the body of the in-line thermometer it runs across the 2-inch thermometer probe, giving an instant and incredibly accurate reading of its exact temperature. Ryan Barto, our Fulfillment Operations Manager and also the thermometer’s inventor, says that this handy device will help you to keep better control of your mash temperatures, and makes it easier to transfer your wort to your conical through the counterflow chiller.
Limited Availability Deal of the Day: As of this posting, this is marked down to $51.99 as a MoreBeer Deal of the Day. Shipping is also free to addresses in the contiguous US with most $59 Orders. Availability: This is available today only, while supplies last. Quantities are limited. Check the MoreBeer’s Deal of the Day to check today’s offering.
Product Description – Here– Use coupon code BEERDEAL to get this discount.
This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
DCT Foot Operated On Off Switch Foot Pedal Switch – 115V 15A Woodworking and Sewing Machine Foot Pedal Control Switch
More Info
From the product description, check product page for current description, price and availability:
POWER CONTROL FOOT SWITCH: Use the DCT Electric Foot Switch Pedal to activate your woodworking tools, power tools, printing tools, sewing machines, tattoo guns, textile tools, and other crafting tools while keeping your hands free
HANDS-FREE OPERATION: Improve safety and control by using this hands-free electric foot pedal switch on off foot switch; Easily start and stop power tools with this foot activated on off switch; Provides continuous power until turned off
COMPATIBLE WITH YOUR POWER TOOLS: Works with your router, sander, drill press, wood lathe, meat grinder, or other 15 amp power tools and machines (not included); Compatible with variable speed equipment (15 amp foot switch does not allow for speed control)
EASY TO USE: Plug the attached 3 prong power cord into a 115 volt grounded outlet, then plug your tool into the 3-prong receptacle on the base of the foot control on off switch; Push the electric pedal forward for power output, then push again to shut off the power
DURABLE CONSTRUCTION: Plastic texturized pedal top provides maximum durability and foot grip, while the 4-foot (1.2m) long power cord allows for versatile use anywhere; 6 x 3.5 inch (15.2 x 8.9cm) tattoo foot pedal electric switch tapers in height from 1.25 to 2.75 inch (3.2 to 7cm)
I use an on/off foot pedal foot switch (different model, manufacturer and specs) for hands free control of my March Pump while brewing. One foot press turns the pump on or off. Other possible applications could be to control a keg washer or draft line cleaning pump. Always use caution when using your pump with hot liquids. Likewise use caution when using electricity around liquids. Hot liquids and electricity can be dangerous. Always read and follow manufacturer directions.
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
pinned
amazon
Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.
…. and more – wort chillers, site glasses, pickup tubes, false bottoms and more
Mark II Beer Pump via Proflow Dynamics
More Info
From the product description, check product page for current description, price and availability:
MK II High Temperature Magnetic Drive Pump
Stainless Steel Head
110V/60HZ
3.4 meter max head
5 GPM (19L max flow)
Max temperature 248 F/ 120 C
Water resistant casing
25 Watt Wort Pump
1/2 inch fittings
The MK 11 Magnetic Drive Pump is constructed using food-grade materials and handles boiling wort with ease. The magnetic drive functions like a clutch allowing one to slow the flow rate down by putting back pressure on the pump. Since it is centrifugal, it’s not self priming, you must put the pump under the level of the liquid source. This magnetic driven pump allows you to brew with confidence knowing that no contamination will occur from lubricated bearing potentially coming into contact with your liquid (beer).
As of this posting, PFD has this for $99.99.
10% Off! Promo code BREW15% gets you 10% off PFD’s entire homebrew lineup
ANOTHER 10% Off: You get another 10% off by using any of the links in this post. Discount reflected at checkout
The stacking deals make this pump $76.49.
Shipping is an additional cost based on your location. Because of minimum shipping costs, it may make sense to place a larger order. Additional items may ship for minimal cost.
MK II Brewing Pump – remember coupon code BREW15% + any link in this post for ANOTHER 10% off
pinned
This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
greatdeals
Price, promotions and availability can change quickly. Check the product page for current price, description and availability prod:pfdmkii
Price, promotions and availability can change quickly. Check the product page for current price, description and availability. pst:pfdsale
pinned
This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
110V Magnetic Home Brewing System Beer Pump, Food Grade Stainless Steel Head with 1/2” NPT Thread, Advanced High Temperature Resistance System Pump (Stainless Steel Head)
More Info
Highlighted Features
Specifications -- 1/2 inch Inlet & Outlet; 110V/60Hz; 10W rated power; with 19 LPM (5 GPM) max flow rate, our beer pump can lift max 3.4 m (10 ft).
Food Grade Stainless Steel -- Magnetic pump head with 1/2 inch Thread is made of Food grade 304 stainless steel, High resistance to corrosion, Not easy to get dirty, Non-toxic, Environmentally friendly, Lasting brewing pump
No Leak, Good Sealing -- Pump shaft is a closed static seal, Splash proof, Greatly avoiding liquid leakage and Achieving excellent sealing, Easier to prime, Amazing liquid circulation beer pump
No Noise, Quiet Operation -- Main shaft is separated from the impeller, with damping and anti-Vibration function, Reducing the influence of motor vibration on the pump, Low power consumption, High efficiency,Run smoothly, Excellent Repeatable magnetic pump
Easy to Use --- Prime by running liquid through pump prior to turning on; The liquid travels from the bottom of the valve into the pump, and once device is powered on (plugged in to outlet), the propeller circulates liquid for maximum flow; Use to dispense beer, treat water, transfer hot water from your kettle to a mash tun, or recirculate mash wort and sparge and transfer to a brew kettle
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
Lightobject EWP-2502HT6V High Temperature(100°C) Mini DC6V Water Pump, Food Grade, Sous Vide, 15 GPH
More Info
From the product description, check product page for current description, price and availability:
This is a high temperature (up to 105’C) Food grade mini water pump
The shaft is coated with a layer of ZrO2 (zirconium oxide ) for higher temperature handling and better tolerance for acid and alkaline
Made in China
This is a high temperature (up to 105’C) Food grade mini water pump. The shaft is coated with a layer of ZrO2 (zirconium oxide ) for higher temperature handling and better tolerance for acid and alkaline. It’s built by a brushless motor providing smooth and quiet operation than a non-brushless water pump. Plus, it will not generate ‘electric spark’ like what a brush type does so it’s more safe. It can be used to pump oil as well (no gasoline*) Specification: Input: DC 5~6V Output: 1.0L/min or 0.264 gallon/min Range: 1M (3ft horizon) @6V Current: 300mA@6V Intake: 0.35in Dia. Outlet: 0.27in Dia. Life span: 6V @ 1600rpm~4200rpm Noise:20dB Working Temp: 212’F (non-submersed) : less than 122’F(submersed) Size(L*W*D): 1.3″ X 0.9″ X 1.4″ Weight (net): 2.0oz Warning: Do not let it run dry without water flow!.
From HBF: Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.
If you’re looking for a small pump to include in your system build or project. In my opinion this is not a direct one to one replacement for something like a Chugger Pump or a March Pump the flow rate isn’t there and the inlet and outlets look small. I do see some possible homebrewing applications including… Transferring wort, mash or sparge water within your system, recirculating mash to help keep a consistent temperature and recirculating wort for chilling. Note that this is 6V DC. You need to wire this up to a compatible power supply.
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
Price, promotions and availability can change quickly. Check the product page for current price, description and availability. pst:pfdsale
pinned
This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
From the product description, check product page for current description, price and availability:
Introducing the X-Dry Series Chugger Pumps! These pumps offer the same great quality we’ve come to expect from Chugger, but now feature Run-Dry Protection. Although the Chugger still needs to be primed before each use, the X-Dry Series offers a new level of protection from damage due to cavitation.
The Chugger lineup of pumps represents a great value for an even better price. These pumps are workhorses in the brewery. Featuring a robust flow rate of 7 gpm, and a magnetic drive designed to handle back-pressure, these pumps are a great addition to any brewing setup! The Stainless Steel Chugger showcases their molded Stainless Steel Pump Head. This stainless pump is a steal for the price, and we’ve been more than happy with the quality! Use this to ease transfers between kettles, cool wort via a counterflow chiller, or recirculate icewater for quicker chilling!
The Chugger pump has 1/2″ mpt inlet and outlet, allowing easy configuration for any application! We recommend setting these pumps up with a Ball valve on the outflow side, this way you can throttle down the outgoing flow rate, allowing for more efficient sparges or cooling! The pump head can also be rotated 360° (in 90° intervals) allowing for even more customization!
Features:
Run Dry Carbon Bearing
Stainless Steel Pump Head
Food Grade up to 250° F
1/2″ mpt inlet and outlet
High Flow rate of 7 gpm
Max Head 18.6 ft
115v 55″ cord and plug attached
50/60 Hz, 1.4 amp
1/20 HP, 3500 RPM
No more issues with crossthreading plastic heads or snapping off fittings
Limited Availability Deal of the Day: As of this posting, this is marked down to $149.99 as a MoreBeer Deal of the Day. Shipping is also free to addresses in the contiguous US with most $59 Orders. Availability: This is available today only, while supplies last. Quantities are limited. Check the MoreBeer’s Deal of the Day to check today’s offering.
Product Description – Here– Use coupon code BEERDEAL to get this discount.
This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
From the product description, check product page for current description, price and availability:
You likely want to monitor the temperature of your wort as it moves from the chiller to the fermenter, and now you can do just that with this In-Line Thermometer. This high quality thermometer features stainless steel quick disconnects for easy installation in line with the rest of your brewing system, and many users install it on the “out” side of their convoluted heat exchangers and counterflow chillers.
As the wort runs through the body of the in-line thermometer it runs across the 2-inch thermometer probe, giving an instant and incredibly accurate reading of its exact temperature. Ryan Barto, our Fulfillment Operations Manager and also the thermometer’s inventor, says that this handy device will help you to keep better control of your mash temperatures, and makes it easier to transfer your wort to your conical through the counterflow chiller.
Limited Availability Deal of the Day: As of this posting, this is marked down to $51.99 as a MoreBeer Deal of the Day. Shipping is also free to addresses in the contiguous US with most $59 Orders. Availability: This is available today only, while supplies last. Quantities are limited. Check the MoreBeer’s Deal of the Day to check today’s offering.
Product Description – Here– Use coupon code BEERDEAL to get this discount.
This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
Magnetic Drive Home Brew Beer Siphon and Water Circulation Pump – Stainless Steel Head with 1/2in Thread
More Info
From the product description, check product page for current description, price and availability:
[Safely Transfer Liquids]: Use the G. Francis Magnetic Drive Home Brew Beer Siphon and Water Circulation Pump to transfer hot and cold liquids instead of trying to move giant brew kettles yourself and running into accidents and injuries; Transferring liquids is a part of any homebrew operation, and this magnetic drive pump is an optimum liquid transport pump with high output volume and quiet operation for industrial and home equipment
[Easy to Use]: Prime by running liquid through pump prior to turning on; The liquid travels from the bottom of the valve into the pump, and once device is powered on (plugged in to outlet), the propeller circulates liquid for maximum flow; Use to dispense beer, treat water, transfer hot water from your kettle to a mash tun, or recirculate mash wort and sparge and transfer to a brew kettle
[Built to Last]: Stainless-steel head, magnetic pump, plastic head for strength and longevity; Safe for beverages, resistant to abrasion, corrosion, and heat up to 221 degrees Fahrenheit (105 degrees Celsius); 6.5-inch x 2.6-inch (15.5cm x 6.4cm) pump overall dimensions with 3.25-inch x 2.5-inch (8.3cm x 6.4cm) steel mounting plate (mounting hardware not included)
[Magnetic]: Fully sealed pump motor with connecting magnetic shaft and magnetic propeller; Magnetically coupled for enhanced operation
[Specifications]: 4.75-foot (1.4m) long 3-prong 18AWG power cord; 1/2-inch NPT thread; 110V; Not self-priming (do not run dry); 5 gallons per minute (19 L/min) maximum capacity; 11.2-foot (3.4m) maximum head; 10W rated power; 150mA current; 60 Hz frequency; 3,000 r/min speed
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
Safely Transfer Liquid: note: This is a magnetic drive pump, not a self-priming pump, please install the pump at least 12 inches lower than your vessel, the pump needs to be filled with liquid before turning on the power, otherwise the liquid will be transported extremely slowly (mishandling). Not for use with high viscosity liquids. Transferring liquids is an important part of any brew operation, and the most easy and safe way to transferring liquids is to use magnetic pump, the propeller will magnetically circulates liquids.
Quiet and Efficient: The pump’s main shaft is separated from the impeller, which has damping and anti-vibration function, aim to reduce the influence of motor vibration during working. Realized a high efficiency smooth running, and excellent quiet circulation. Maximum Lifting Height: 2.7Meters. Please note: Moving giant vessel with hot wort by hand is not safe
Solid Magnetic Pump: Fully-sealed magnetic pump, motor with connecting the magnetic shaft and magnetic propeller, all magnetically coupled for enhanced operation. This is a High output volume and quiet operation pump, industrial and home brew equipment. Great heat resistant up to 120℃/ 248℉
Easy to Use: Prime by running liquid through the pump by connecting with water hose prior to turning it on; The liquid travels from the water hose into the pump, and once the pump is powered on, the propeller will start to circulate the liquids; Perfect for transferring and circulation
After-Sales Service: We are committed to offer you high quality product as well as superior service! Please feel free to tell if any problem, we would try our best to help. Provide technical support. It is not recommended to run this pump continuously for more than 2 hours to avoid overheating of the motor
I use my homebrew pump (different model and different manufacturer) for vorlaufing/recirculating, transferring from my mash tun to brew kettle, chilling with a recirculating wort chiller and transferring to my fermenter.
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
110V Magnetic Home Brewing System Beer Pump, Food Grade Stainless Steel Head with 1/2” NPT Thread, Advanced High Temperature Resistance System Pump (Stainless Steel Head)
More Info
Highlighted Features
Specifications -- 1/2 inch Inlet & Outlet; 110V/60Hz; 10W rated power; with 19 LPM (5 GPM) max flow rate, our beer pump can lift max 3.4 m (10 ft).
Food Grade Stainless Steel -- Magnetic pump head with 1/2 inch Thread is made of Food grade 304 stainless steel, High resistance to corrosion, Not easy to get dirty, Non-toxic, Environmentally friendly, Lasting brewing pump
No Leak, Good Sealing -- Pump shaft is a closed static seal, Splash proof, Greatly avoiding liquid leakage and Achieving excellent sealing, Easier to prime, Amazing liquid circulation beer pump
No Noise, Quiet Operation -- Main shaft is separated from the impeller, with damping and anti-Vibration function, Reducing the influence of motor vibration on the pump, Low power consumption, High efficiency,Run smoothly, Excellent Repeatable magnetic pump
Easy to Use --- Prime by running liquid through pump prior to turning on; The liquid travels from the bottom of the valve into the pump, and once device is powered on (plugged in to outlet), the propeller circulates liquid for maximum flow; Use to dispense beer, treat water, transfer hot water from your kettle to a mash tun, or recirculate mash wort and sparge and transfer to a brew kettle
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
Northern Brewer – Anti Gravity Self Priming Beer Transfer Pump Kit
From the product description, check product page for current description, price and availability:
The Anti-Gravity Transfer Pump Kit is a bite-sized package that revolutionizes your brewery’s efficiency.
This kit, complete with self-priming diaphragm pump, tubing, and a premium stainless steel racking cane.
Transfer from primary to secondary, conical to keg, carboy to barrel – the possibilities are endless!
Simply flip a switch to move any liquid imaginable from one vessel to another.
We realize you won’t be able to actually defy gravity, but this little pump has some incredible lifting abilities that allow you to send your beverages from the floor up to your awaiting vessel.
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
From the product description, check product page for current description, price and availability:
[Safely Transfer Liquids]: Use the G. Francis Magnetic Drive Home Brew Beer Siphon and Water Circulation Pump to transfer hot and cold liquids instead of trying to move giant brew kettles yourself and running into accidents and injuries; Transferring liquids is a part of any homebrew operation, and this magnetic drive pump is an optimum liquid transport pump with high output volume and quiet operation for industrial and home equipment
[Easy to Use]: Prime by running liquid through pump prior to turning on; The liquid travels from the bottom of the valve into the pump, and once device is powered on (plugged in to outlet), the propeller circulates liquid for maximum flow; Use to dispense beer, treat water, transfer hot water from your kettle to a mash tun, or recirculate mash wort and sparge and transfer to a brew kettle
[Built to Last]: Stainless-steel head, magnetic pump, plastic head for strength and longevity; Safe for beverages, resistant to abrasion, corrosion, and heat up to 221 degrees Fahrenheit (105 degrees Celsius); 6.5-inch x 2.6-inch (15.5cm x 6.4cm) pump overall dimensions with 3.25-inch x 2.5-inch (8.3cm x 6.4cm) steel mounting plate (mounting hardware not included)
[Magnetic]: Fully sealed pump motor with connecting magnetic shaft and magnetic propeller; Magnetically coupled for enhanced operation
[Specifications]: 4.75-foot (1.4m) long 3-prong 18AWG power cord; 1/2-inch NPT thread; 110V; Not self-priming (do not run dry); 5 gallons per minute (19 L/min) maximum capacity; 11.2-foot (3.4m) maximum head; 10W rated power; 150mA current; 60 Hz frequency; 3,000 r/min speed
I use my homebrew pump (different model and different manufacturer) for vorlaufing/recirculating, transferring from my mash tun to brew kettle, chilling with a recirculating wort chiller and transferring to my fermenter.
This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!
Anti-Gravity Transfer Pump by BrewVint via Adventures in Homebrewing
More Info
From the product description, check product page for current description, price and availability:
The Anti-Gravity Transfer Pump is great for transferring beer, wine, water, or any other fermented beverage you may be working on. No more heavy lifting when transferring from your keg, carboy, fermenter, bucket, or cooler! It’s as simple as hooking up the self-priming pump and flipping on the switch. Transfer from one vessel to another with endless possibilities. This does not include tubing or a racking cane, please see our add-on section and make sure you pick the right hose for your needs. We recommend using 5/16″ I.D. x 7/16″ O.D. hoses.
Self Priming with a Food Grade Pump Head
12V adapter included with 8 ft Power Cord
In-line On/Off switch
Flow-rate of 1.05 GPM
Suction Ability 5 Feet
Integrated locking tubing collars
Liquid Temperature Rating up to 140 Degrees
Max lift of 150 ft
Stacks With Free Shipping: Adventures in Homebrewing is offering free shipping on most orders of $55 or more to addresses in the contiguous US.
This post contains affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
pinned
aih
Check sale or product page for current availability & pricing
Price, promotions and availability can change quickly. Check the product page for current price, description and availability. tag:aihperoff
Check sale or product page for current availability & pricing
