How To: Step by Step Making a Magnetic Drip Tray
Pictured: Update International (DTS-419) 4″ x 19″ Rectangular Drip Tray, Stainless Steel – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link
Step by Step instructions for making a magnetic drip try for your Kegerator or Keezer.
This is a project that requires materials and tools. Operate power tools carefully. Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.
By: HBF Reader Andrew Cunje
Materials:
- Update International (DTS-419) 4″ x 19″ Rectangular Drip Tray, Stainless Steel – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link
- Alternate: DasMarine 19″ Length 4″ Width Rectangular Stainless Steel Beer Surface Mount Drip Tray
- 4′ of 6x.5 Poplar Wood (actual width is 5.5″)
- 1’4″ of 6×1 Poplar Wood (actual width is 5.5″) Note: A thicker wood will suffice for this…remember the longer the wood extends down from the joint, the less likely the magnetic bond will break from the leverage applied to the edge of the drip tray.)
- 4-5ft of Decorative Trim of your choice (Sold in lengths of 8′)
- MUST BE 1.25-1.5 inch trim. I used 1.5 which I highly recommend.
- 3/4″ mounting screws (for magnets) or Epoxy/Gorilla Glue
- 1″ wood screws
- Brad/Finishing Nails
- 1 large old school hard drive magnets (Bigger with Mounting Holes than newer drives) (Alternative: rare earth neodymium magnets that are .5″ thick (Approximately 8); these can be stacked if you can only find .25″ magnets)
- Wood Glue
- Wood Putty (Optional)
- Wood Stain (Optional)
- Tennis Racket Grip Tap (Or an old yellow rubber glove). Anything rubbery and tacky to increase friction against the fridge.
This article contains affiliate links. We may make a small percentage if you use our links to make a purchase. You won’t pay more and you’ll be supporting Homebrew Finds and more content like this. Thank you for your support!
Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.
Tools Needed:
- Beer – 🙂
- Measuring Tape & Straight Edge
- Pencil
- Saw
- Hammer
- Brad tool (to push head of brad beneath wood surface) (Optional)
- Drill
- Drill bits
- Counter Sink Bit
- Sand Paper
Directions:
- Wooden Drip Tray Base: Cut the 6″x.5″ poplar to the length of your Drip tray. This must be as long or longer to accommodate the trim added later. Sand burrs (This step will be omitted from all other wood cutting steps. This should be common sense, if it’s not, return all the stuff you bought and buy a pre assembled drip tray with mount for installation.)
- Front Drip Tray Trim: Cut the decorative trim to the length of the board you cut PLUS 2x the thickness (depth) of the trim. MEASURE TWICE CUT ONCE! For instance your front trim piece for the 19″ drip tray should be Length of drip tray + .25″ +.25″. This will allow the trim to hang over the length and cover the side piece of the drip tray.Note: If you accidentally cut this to the exact width of the drip tray, don’t fret. You will need this piece to fill the gap behind the drip tray.
- Side Drip Tray Trim: Cut the decorative trim to the width of the drip trap base depth. This should be 5.5″ inches! (a 6″x.5″ is actually 5.5″x.5″) You will need TWO of these (left and right side trims). You can optionally cut this to 6 inches to accommodate for the depth of the magnets…I choose not to because I didn’t think of it at the time.
- Assemble upper Drip Tray Mount (Attach Trim to Wooden Drip Tray Base): The trim can now be attached to the base. I used Wood Glue and Brads. 2 brads on the sides and 4 on the front. I used a special tool to push the brad heads below the surface of the wood and filled with wood putty. Be sure to have a damp paper towel to clean up excess putty and wood glue.
- Drink beer now. You’re getting there.
- Create the Wooden L Bracket (Attaching the upper and lower portions of the wooden trip tray mount): Attach the upper drip tray mount to the 1’4″ of 6×1 Poplar Wood. I used 5 screws, evenly spaced to do this. I centered it and pre drilled all holes. Use the 1″ wood screws here and be sure to counter sink them. You can fill the countersunk screws with wood putty.Note: The length of wood that attaches to the kegerator should be >= the length that the drip tray extends away from the kegerator. simple physics, so you can negate the torque of the weights/load acting as a lever on your magnets!
- Rear plank torque extension plate: Attach approximately 6-8 inches of the excess 6x.5 (cut to length) to the center of the rear of the lower drip tray. Use your counter sink and 3/4″ screws here. This piece is crucial for stability of the mount. it ensures that additional grip is provided to the surface and minimizes the pressure points created by your magnets.
- Attach magnets evenly in the space left on the rear of the bracket. I placed them two inches from the end of this rear portion of the mount. User you 3/4″ screws here. I had to drill out the magnet bracket holes to get the screws to work. If your magnets don’t have mounting holes or you couldn’t acquire these old magnets…attach you alternative 1/2″ magnets with epoxy or gorilla glue…do not get it on the surface that will contact the fridge! Follow manufacturers dry times for that option. NO MATTER what magnets you use…they must be .5 inches…they have to be the same depth as the rear plan extension.Note: The magnet placement should be towards the top of the empty space…i did centered…which is much less efficient…but i still got 10# on it…probably don’t need more than that though!
- Get a grip: Finally, attach your tennis grip tape (or alternative) using 3m spray adhesive or double sided tape (The thinner the better) to the Rear plank torque extension plate and magnet surfaces that will contact your kegerator/keezer. This will prevent damage to the freezer surface and magnets. It will additionally increase the friction provided by your 2+ magnets to increase the holding power without having to go magnet crazy
- Insert your drip tray to your bracket…pretty self explanatory
- Fill the gap: Using your excess decorative trim, cut a piece of trim to the length of the first piece of wood you cut or the distance between the side trims. Place this between the drip tray (stainless steel) and the fridge. This will hide your screw holes and add to the pizzazz of your project
- Mount to fridge and test fitment…guess and check here…if magnets and rear plank make contact, you should be good to go for weight testing! Don’t use beer in case you totally mess it up. After all is good… pour a beer…rest it on your weight tested drip tray and admire your almost completed work.
- Take the tray off the fridge…with your beer in hand go outside and Stain or paint your drip tray as needed.
- THE END!
Photos:
- Update International (DTS-419) 4″ x 19″ Rectangular Drip Tray, Stainless Steel – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link
- Alternate: DasMarine 19″ Length 4″ Width Rectangular Stainless Steel Beer Surface Mount Drip Tray
Related: Hands on Review: Budget Magnetic Drip Tray
Also: Kegerator Tips & Gear | Keg Repair Part #s | Recent Keg Finds
Our Top Draft Resources!
Check our our Top Draft Related Resources- The Most Difficult Spot to Check for CO2 Leaks
- Keg O-Ring Materials Selection! – EPDM, Silicone and Buna-N?
- Why Do I Have Bubbles in My Beer Line? Diagnosing and Fixing Kegerator Foam Problems
- Five Benefits of Using Corny Kegs As Fermenters
- Rebuilding & Reconditioning Homebrew Kegs!
- Food Safe Replacement Keg O-Rings in Bulk
- Hands on Review: Kegland DuoTight Fittings & EVABarrier Tubing!
- Why Won’t My Homebrew Keg Carbonate? Fixing Draft Beer Carbonation Problems
- What Does a Flow Control Faucet Do?
- Upgrade Your Kegerator – 6 Improvements!
- Serve Homebrew on Any Kegerator & Convert Commercial Kegerator to Homebrew
- Tips and Gear for Growler Filling
- What’s the Difference Between Ball Lock Kegs and Pin Lock Kegs?
- Checking for Draft System CO2 Leaks – Using The Pressure Gauge Method
- Tip: Consider Oetiker Stepless Clamps for Kegerator Gas and Beer Lines
- Hands On Review: Inkbird ITC-308 Dual Stage Temperature Controller +WiFi Version
- Universal Poppets Tips and Tricks!
- Convert Your Mark II Keg & Carboy Washer to a Recirculating Draft Line Cleaning Pump!
- Step by Step: Finding and Fixing Keg CO2 Leaks
- Kegerator Beer Line Temperatures & Reducing Foam with a Recirculating Fan
- Kegging CO2 Use Estimations and Calculations
- Step by Step: Balancing Your Kegerator Draft System
- Building a Simple Ball Lock Draft Line Flushing Setup
- Build a Recirculating Draft Line Cleaning Pump
- Home Brew Keg Roundup – New & Used, 5 and 2.5 Gallon & More!
- Damp Kegerator? Fix Kegerator Condensation
- Portable Draft Beer Serving Options!
- Homebrew Temp Controller Roundup! – Kegerator and Fermentation – concepts, applications and models
- Bulk Keg Orings and Keg Repair Part Numbers
More Homebrew Finds!
- Last 50 Finds!
- Top Deals – a curated list of the best deals
- Homebrew Reviews – one of the largest libraries of homebrew reviews in existence!
- Our Top Posts – tips, how-tos, resources posts and more
- Let’s be Friends!
Recent Deals!
10 Most Recent Homebrew Resource Posts & How-To’s!
We are Homebrew Review HQ! Our 10 Most Recent Reviews
This post may contain affiliate links. We may make a commission when you use our links. This will never cost you extra. Thank you for supporting Homebrew Finds!
greatdealsThis is a Top Post! See: All Top Posts
Price, promotions and availability can change quickly. Check the product page for current price, description and availability. tag:lnksfxd toppost:magdriptray tag:tpr
Thanks for sharing. Great detail in the images. Keep up the great work.
https://vimeo.com/tdubphotography